Sony DVCAM DSR-PDX10 Service Manual page 229

DSR-PDX10/PDX10P
3-1-2. Precautions on Adjustment
Note1: Before performing the adjustments, check the data of page: 0,
address: 10 is "00". If not, set data: 00 to this address.
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR" (or
"PLAYER") or set the "Forced VTR Power ON mode" using
the adjustment remote commander (Note2).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note3).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note5)
2) Cabinet (R) (CK-134 board, LCD block) need not be connected.
But removing the cabinet (R) (removing the CK-134 board
CN5203) means removing the lithium 3V power supply (CK-
134 board, BT5201) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the cabinet (R) has
been removed. (Refer to "6-4.Service Mode" for the data on
the history use and the self-diagnosis data.)
To remove the cabinet (R), disconnect the following connector.
CK-134 board CN5203 (60P, 0.5mm)
3) The front panel block (MA-425 board, focus ring, microphone
unit)) need not be connected except for the audio system
adjustments. To remove it, disconnect the following connectors.
MA-425 board CN5906 (33P, 0.5mm)
MA-425 board CN5904 (8P, 0.5mm)
4) The EVF block (LB-089 board) and the intelligent accessory
shoe are need not be connected. To remove it, disconnect the
following connectors.
DB-016 board CN7211 (21P, 0.3mm)
DB-016 board CN7205 (27P, 0.3mm)
5) The memory stick connector (FP-503 flexible) is need not be
connected. To remove it, disconnect the following connector.
VC-318 board CN1009 (10P, 0.5mm)
6) The control switch block (CF-1870) is need not be connected.
To remove it, disconnect the following connector.
DB-016 board CN7200 (8P, 0.5mm)
7) By setting the "Forced VTR Power ON mode", the video section
can be operate even if the control switch block (PS-1870) has
been removed. When removing it, disconnect the following
connector.
DB-016 board CN7201 (6P, 0.5mm)
9) The lens block (CD-389 board) is need not be connected. To
remove it, disconnect the following connectors.
VC-318 board CN1201 (60P, 0.5mm)
DB-016 board CN1501 (10P, 0.5mm)
DB-016 board CN1004 (39P, 0.3mm)
Note2: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned
on with the control switch block (PS-1870 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note3: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-1870 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note4: Setting the "Forced Memory Power ON" mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the memory power to be turned
on with the control switch block (PS-1870 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note5: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
3-1-3. HOW TO ENTER RECORD MODE WITHOUT
CASSETTE
1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button.
(The mechanism enters the record mode automatically.)
Note: The function buttons becomes inoperable.
5) To quit the record mode, select page: 3, address: 01, set data:
00, and press the PAUSE button. (Whenever you want to quit
the record mode, be sure to quit following this procedure.)
3-1-4. HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE
1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button.
(The mechanism enters the playback mode automatically.)
Note: The function buttons becomes inoperable.
5) To quit the playback mode, select page: 3, address: 01, set data:
00, and press the PAUSE button. (Whenever you want to quit
the playback mode, be sure to quit following this procedure.)
6-74