Sony DVCAM DSR-PDX10 Service Manual page 175

DSR-PDX10/PDX10P
1-2-4. INITIALIZATION OF B, 1B PAGE DATA
Note: When reading or writing the B page data, select page: 0, address:
10, and set data: 00.
When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
"00".
1. Initializing the B, 1B Page Data
Note1: If "Initializing the B, 1B Page Data" is performed, all data of the
B page and 1B page will be initialized. (It is impossible to initialize
a single page.)
Note2: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Initializing Method:
Order Page Address Data
1 0 01
2 0 10
3 5 0E
4 5 01
5 5 00
6 5 0E
7 5 0E
8 5 03
9 5 01 FA
10 5 00
11 5 0E
12
B
00 to FF
1B
00 to FF
Procedure
01 Set the data.
00 Set the data.
00 Set the data, and press PAUSE
button
F3 Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data changes to
"01".
00 Set the data, and press PAUSE
button
20 Set the data, and press PAUSE
button.
Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data changes to
"01".
Turn off the power and turn on
again
2. Modification of B, 1B Page Data
When changing the B, 1B page data, change the data by the following
procedure.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) When changing the B page data, select page: 0, address: 10,
and set data: 00.
3) When changing the 1B page data, select page: 0, address: 10,
and set data: 01.
After completing the modification of 1B page data, reset the
data of this address to "00".
4) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of B, 1B Page data:
Order Page Address Data
1 0 10
2 2 00
3 2 01
3. B Page Table
Note1: The data of page: 0, address: 10 must be "00".
Note2: Fixed data-1: Initialized data. (Refer to "1. Initializing the B, 1B
Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of B, 1B
Page Data").
Address
00 to FF Fixed data-1
4. 1B Page Table
Note1: When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
"00".
Note2: Fixed data-1: Initialized data. (Refer to "1. Initializing the B, 1B
Page Data".)
Fixed data-2: Modified data. (Refer to "2. Modification of B, 1B
Page Data").
Address
00 to FF Fixed data-1
6-20
Procedure
00 Set the data.
29 Set the data.
29 Set the data, and press PAUSE
button.
Remark
Table. 6-1-10.
Remark
Table. 6-1-11.