Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 279

Pos : 769 /Allgemein/Steuer module/Stichwortverzeic hnis @ 0\mod_1317978518730_14638.doc x @ 14772 @ @ 1
Key word index
=== Ende der Liste für T extmar ke Stichwortverzeic hnis ===
"
"Overtemperature" ....................................... 226
3
3-wire control ............................................... 177
3-Wire Ctrl.................................................... 177
A
Absolute min. freq. (P505) ........................... 189
Acceleration time (P102) ............................. 139
Actual bus value 1 ... 3 (P543) .................... 201
Actual frequency processing ....................... 275
Actual values ............................................... 274
Additional parameters .................................. 187
Address........................................................ 277
Adjustment range
1/10 ......................................... 267, 270, 272
1/17 .......................................................... 271
Amplification ISD control (P213) ................. 150
Analog input adjustment
0% (P402) ................................................ 170
100% (P403) ............................................ 171
Analog input filter (P404) ............................. 171
Analog input voltage (P709) ........................ 211
Apparent power (P726) ............................... 213
Array parameters ......................................... 136
AS interface ................................................. 119
ATEX .......................................... 25, 29, 44, 75
ATEX
ATEX zone 22, cat. 3D .............................. 76
ATEX
Optional ATEX modules ............................. 77
ATEX
EU conformity declaration .......................... 81
ATEX
ATEX zone 22, cat. 3D .............................. 82
Automatic fault acknowledgment. (P506) .... 189
Automatic magnetization adjustment (P219)
................................................................. 152
Automatic magnetization optimization ......... 266
Automatic start (P428) ................................. 179
B
Basic parameter .......................................... 139
Boost derivative action (P215)..................... 150
Boost derivative action time (P216) ............. 151
Brake chopper ............................................... 52
Brake control ....................................... 142, 145
BU 0200 en-US-3118
Brake distance ............................................ 143
Brake reaction time (P107) ......................... 142
Brake release time (P114) .......................... 145
Braking resistor ..................................... 52, 240
Braking resistor (P556) ............................... 205
Braking resistor type (P557) ....................... 205
Bus
setpoint (P546) ........................................ 202
Bus I/O In Bits ............................................. 184
Bus I/O Out Bits .......................................... 184
Bus setpoints ...................................... 202, 204
Bus status via PLC (P353) .......................... 162
C
CAN
address (P515) ........................................ 192
CAN bus baud rate (P514) ......................... 191
CAN master cycle (P552) ........................... 203
CANopen status (P748) .............................. 218
CE label ...................................................... 252
Charging error ............................................. 235
Chopper P limit (P555)................................ 205
Configuration level (P744) .......................... 218
conformity declaration
ATEX ......................................................... 81
Contact ........................................................ 277
Control connection ........................................ 65
Control options ........................................ 86, 89
Control parameter ....................................... 155
Control terminals ..................... 67, 73, 122, 164
Control unit connection ................................. 65
Control word source (P509) ........................ 190
COPY .......................................................... 111
Copy function .............................................. 111
Copy parameter set (P101) ........................ 139
CSA ............................................................. 239
cUL .............................................................. 239
Current
phase U (P732) ....................................... 214
phase V (P733) ....................................... 214
phase W (P734) ...................................... 215
Current limit (P536) ..................................... 198
Current vector control ................................. 152
Curve setting ............................... 149, 150, 152
Customer unit ................................................ 89
Key word index
279