Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 231

Pos : 663 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E013 [SK 200E ... SK 5xxE] @ 2\mod_1347454271218_14638.doc x @ 46752 @ @ 1
E013 13.0 Encoder error
13.1 Speed slip error
"Speed slip error"
13.2 Disconnect. control,
"Shut-down monitoring"
13.5 Reserved
13.6 Reserved
Pos : 664 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E014 "res er viert" [SK 200E ... SK 5xxE] @ 2\mod_1347454273854_14638.doc x @ 46777 @ @ 1
E014 --- Reserved
Pos : 665 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E015 [SK 180E ... SK 5xxE] @ 2\mod_1347454278051_14638.doc x @ 46802 @ @ 1
E015 --- Reserved
Pos : 666 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E016 [SK 135E ... SK 5xxE, SK xxxE-FDS] @ 2\mod_1347454280625_14638.doc x @ 46827 @ @ 1
E016 16.0 Motor phase error
16.1 Magn. Current Watch
"Magnetizing current
monitoring"
Pos : 667 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E018 "res er viert" [SK 2xxE/SK 5xxE/SK 2xxE-FDS] @ 2\mod_1347454282777_14638.doc x @ 46852 @ @ 1
18.0 Reserved
E018
Pos : 668 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E019 [SK 180E/SK 2xxE/SK 5xxE/SK2xxE-FD S] @ 2\mod_1347454285788_14638.doc x @ 46877 @ @ 1
E019 19.0 parameter ident.
"Parameter identification"
19.1 Star/delta incorrect
"Motor star/delta circuit
incorrect"
Pos : 669 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265496 @ @ 1
BU 0200 en-US-3118
6 Operating status messages
No signal from encoder
• Check 5 V sensor if available
• Check supply voltage of encoder
The slip speed error limit was reached.
• Increase value in P327
The slip error monitoring was triggered; the motor could not
follow the setpoint.
• Check motor data P201-P209! (important for current
controllers)
• Check motor circuit
• Check encoder settings P300 and following in servo
mode
• Increase value for torque limit in P112
• Increase value for current limit in P536
• Check deceleration time P103 and extend if
necessary
Error message for POSICON  see supplementary manual
Error message for POSICON  see supplementary manual
Error message for POSICON  see supplementary manual
A motor phase is not connected.
• Check P539
• Check motor connection
Required exciting current not achieved at moment of switch-
on.
• Check P539
• Check motor connection
Error message for "safe pulse block"  see supplementary
manual
Automatic identification of the connected motor was
unsuccessful
• Check motor connection
• Check preset motor data (P201 ... P209)
• PMSM – CFC Closed Loop Operation: Rotor position
of motor incorrect in relation to incremental encoder
Determine rotor position (initial enable after a "Power
On" only with motor stationary) (P330)
231