Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 134

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 283 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_4-Steuer klemmen [SK 1x0E, SK 2xxE] @ 9\mod_1447414720702_14638.doc x @ 263609 @ @ 1
Control terminals
P400 Function Setpoint inputs
P403 Adjustment: 100%
P411 Max. freq. Auxiliary
setpoint
P414 PI controller I comp.
P417 Analog output offset
P420 Digital inputs
P428 Automatic start
P436 Dig. out. hysteresis
P465 Fixed freq. field
P480 Function BusIO In bits
P483 Hyst. BusIO Out bits
Pos : 284 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_5-Z usatzpar ameter [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 9\mod_1447415583483_14638.doc x @ 263642 @ @ 1
Additional parameters
P501 Inverter name
P504 Pulse frequency
P509 Source control word
P512 USS address
P515 CAN address
P518 Skip frequency 2
P521 Flying restart circuit
Resolution
P525 Load control max
P528 Load monitoring delay
P534 Torque shutoff limit
P537 Pulse disconnection
P541 Set relays
P546 Function bus setpoint
P552 CAN master cycle
P556 Braking resistor
P559 DC run-on time
Pos : 285 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_6-Positi oni erung [SK 2xxE, SK 2xxE-FDS] @ 9\mod_1447415705800_14638.doc x @ 263675 @ @ 1
Positioning
P600 Position control
P603 Actual pos. diff.
P607 Transformation ratio
P610 Setpoint mode
P613 Position
P625 Output hysteresis
P631 Slip error Abs./inc.
Pos : 286 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265496 @ @ 1
134
P401 Analog input mode
P404 Analog input filter
P412 Process controller
setpoint
P415 Process controller limit
P418 Function Analog output
P426 Quick stop time
P434 Digital output function
P460 Watchdog time
P466 Minimum freq. process
controller
P481 Function BusIO Out bits
P502 Master function value
P505 Absolute minimum freq.
P510 Source setpoints
P513 Telegram timeout
P516 Skip frequency 1
P519 Skip freq. area 2
P522 Flying restart circuit Offset
P526 Load control min
P529 Load control mode
P535 I²t motor
P539 Output monitoring
P542 Set analog output
P549 Pot box function
P553 PLC setpoint
P557 Braking resistor capacity
P560 Parameter saving mode
P601 Actual position
P604 Distance measuring
system
P608 Reduction ratio
P611 Position controller P
P615 Maximum position
P626 Comparative position
Output
P640 Unit of pos. value
P402 Adjustment: 0%
P410 Min. freq. Auxiliary
setpoint
P413 PI controller P comp.
P416 Ramp time PI setpoint
P419 Standard Analog output
P427 Emerg. stop Fault
P435 Dig. out scaling
P464 Fixed frequency mode
P475 Delay on/off switch
P482 Standard BusIO Out bits
P503 Master function output
P506 Auto. Fault
acknowledgement
P511 USS baud rate
P514 CAN bus baud rate
P517 Skip freq. area 1
P520
Flying restart circuit
P523
Factory setting
P527 Load monitoring Freq.
P533 I²t factor
P536
Current limit
P540 Rotation direction mode
P543 Bus actual value
P550 EEPROM Copy Order
P555 P limit chopper
P558 Magnetizing time
P602 Actual setpoint position
P605 Absolute encoder
P609 Offset position
P612 Target window limit
P616
Minimum position
P630
Position slip error
BU 0200 en-US-3118