Edid Mode; Signal Present Mode - Lightware MX-FR Series User Manual

   
4. Operation
4.7.4. EDID Mode
To enter or to exit from this mode press and release the EDID button.
DDID mode is active when the DDID button is illuminated on the front
panel. All DDIDs are referred with their memory location e.g. F49 or
D03, see the DDID Menu section.
Select menu items with up ▲ and down
▼ buttons and then press enter  or
right ► button to step in submenus.
Press the escape ● button to return to
main DDID management menu.
INFO:
Not executed operation is canceled when exit from the DDID
menu.
INFO:
Source and destination buttons are disabled while DDID
mode is active.
View EDID Menu
All the stored DDIDs can be checked
through this menu. The DDID types are
grouped in submenus.
The most important information
about each DDID is shown in the
submenu.
Use the left ◄ and right ► buttons to
select the desired DDID. The monitor
name and the preferred resolution can
be checked.
Save EDID Menu
The DDID from any connected monitor
can be saved to user memory slots.
Select the dynamic DDID of the output
port with the left ◄ and right ►
buttons. Then press down ▼ and
select the user DDID slot where the
monitor's EDID would be stored.
After the desired dynamic DDID and
user memory is selected, go to Save!
and press the enter  or right ► button
to store the DDID.
Switch EDID Menu
The emulated DDIDs can be changed
in this menu. Dynamic, User or Factory
DDIDs can be selected in the top row
with the left ◄ and right ► buttons. The
preferred resolution of the selected
DDID is shown in the second row of
EDID management
the screen.
~View EDID >>
Save EDID
Press down ▼ and then select the
Switch EDID input port with the left ◄ and right ►
buttons.
After the desired DDID and input port
is selected, go to Do switch! and press
enter  or right ► button to change the emulated DDID.
The Operation in progress message appears on the LCD. If switching the
DDID succeed then Operation done! message is shown for 2 seconds.
4.7.5. Signal Present Mode
View EDID
~Dynamic EDIDs >>
Press the Signal present button to enter or exit this mode. The
Emulated EDIDs Signal present mode is active when the button is illuminated.
Factory EDIDs
In this mode the source and destination buttons show the
actual connection state of the corresponding port, and the actual
crosspoint state can be checked on the LCD menu.
Dynamic EDIDs
<EDID mem: D15 >
Press up ▲ or down ▼ buttons to navigate between the submenus and
PHL Philips 230W5
screens.
1920x1200@59.94Hz

AAAENAIONG!
Signal Present mode is active.
Source and Destination Buttons
EDID Save
If a source button is illuminated then a signal is present on that
<Dynamic EDID D6 >
source. If a destination button is illuminated then a powered display is
to User EDID U2
attached to this output (Hot Plug Detect signal is present).
Save!

INFO:
to sense signals and monitors, therefore this function could be
EDID Save inadequate with certain I/O boards.
Dynamic EDID D6

TIPS AND TRICCS:
to User EDID U2
this feature.
~Save! >>
MX-FR Series Modular Matrix Frames – User's Manual
<Switch EDID: F21
LWR D1600x1200p60
to input: 4
Do switch!
Switch EDID: F21
LWR D1600x1200p60
to input: 4
~Do switch!
Source and destination buttons are disabled while
Keep in mind that I/O boards have different capabilities
You can quickly check the cable connections by
Signal on Aest Input
This screen shows the
>
incoming signal resolution on the Test
input port.
Press up ▲ or down ▼ button to go to
the previous or next screen.
Signal on Preview Output
This screen shows the actual signal
resolution that presents on the
Preview output port.
Press up ▲ or down ▼ button to go to
>>
the the previous or next screen.
Crosspoint Status
Navigate to the Crosspoint submenu
item with up ▲ and down ▼ buttons
and then press enter  or right ►
button to step in this submenu.
SIGNAL
The crosspoint connections
PRESENT
shown. One screen shows connected inputs for nine outputs. Further
outputs can be checked by scroll through screens with up ▲ and down
▼ buttons.
Every output's connection is shown like this: 'o01i03'. In this example,
it means that input 3 is connected to output 1.
Press the escape  button to return to the main Signal present menu.
48
actual
Signal present
Test input:
1600x1200p60
Signal present
Preview output:
no signal
Crosspoint status
o01i03 o02i12 o03i12
o04i12 o05i12 o06i12
o07i12 o08i12 o09i12
are