Rj45 Connectors And Twisted Pair Cables - Lightware MX-FR Series User Manual

   
3. Product Overview
Symmetrical Analog Stereo Audio
5-pole Phoenix connector is used for balanced analog audio (line in/out). Some I/O
boards use this connector as a configurable input or output. Always check if this
connector is configured as an output or input to prevent connecting two outputs
together.
1 2 3 4 5
Unbalanced audio signals can be connected as well. For asymmetrical output, connect only + and ground.
For asymmetrical input connect + and ground to the source and connect – to the ground.
Compatible Plug Aype
Phoenix® Combicon series (3.5mm pitch), type: MC 1.5/5-ST-3.5, order number: 1840395.
Please see the short guide about the audio cable wiring in the
3.12.4. RJ45 Connectors and Awisted Pair Cables
Ahe Wiring of Awisted Pair Cables
Lightware recommends the termination of TP cables on the basis of TIA/EIA T 568 A or TIA/EIA T 568 B
standards.
Pin AIA/EIA A568 A Color and name
1 white/green stripe
2 green solid
3 white/orange stripe
4 blue solid
5 white/blue stripe
6 orange solid
7 white/brown stripe
8 brown solid
MX-FR Series Modular Matrix Frames – User's Manual
Pin nr. Signal
1 Left +
2 Left -
3 Ground
4 Right -
5 Right +
Audio Cable Wiring Guide section.
AIA/EIA A568 B Color and name
Side
white/orange stripe
orange solid
white/green stripe
Bottom
blue solid
white/blue stripe
Top
green solid
white/brown stripe
brown solid
MX-AP Input and Output Ports
HDMI-TP and DVI-TP interface boards provide standard RJ-45 connectors for VIDEO IN /
OUT and DDC IN / OUT. Please note that the DDC connector is not available on MX-DVI-
TP-IB and MX-DVI-TP-OB but available on MX-DVI-TP-IB+ and MX-DVI-TP-OB+ boards.
Pin VIDEO IN/OUA
1 TMDS Data0+
2 TMDS Data0-
3 TMDS Clock+
4 TMDS Data1+
5 TMDS Data1-
6 TMDS Clock-
7 TMDS Data2+
8 TMDS Data2-
MX-APS Inputs and Outputs
MX-TPS boards provide standard RJ-45 connectors for TPS extenders or MX boards.
AAAENAIONG!
The same RJ-45 connector is used for Ethernet. Avoid connecting
LAN cable to the TPS connectors. If the port of the TPS board was set to AUTO
mode, it is able to recognize the LAN cable and swap to Dthernet fallback mode
automatically. In this case, the port works as an Dthernet switch, but TPS CAT
cable is not allowed to connect to the Dthernet port!
OFF
1
Blinking
1 flash / sec
8
Blinking
2 flashes / sec
8
Blinking
6 flashes / sec
1
ON
DDC IN DDC OUA
CDC (no conn.) CDC (no conn.)
Hot Plug Detect (in) Hot Plug Detect (out)
RS-232 RX RS-232 RX
DDC CLC DDC CLC
+12V (out) +12V (out)
RS-232 TX RS-232 TX
DDC SDA DDC SDA
GND GND
LED1, Amber LED2, Green
Remote power is
No TPS link
disabled
Low power mode,
N/A
RS-232 and Dthernet
Low power mode,
N/A
only RS-232
N/A Dthernet fallback mode
Remote power is
TPS link is active
enabled
24
8 1
8 1
TPS IN 2