Output Port Status; All Port Status; I/O Port Commands; Tps And Tps2 Port - Lightware MX-FR Series User Manual

   
7. Programmer's Reference
7.8.2. Output Port Status
Description: Shows the actual status of the output ports. The response length changes regarding the frame
size. The meaning of the values changes regarding the output board types as they have different capabilities.
Format
Command {:OSD}
Response (OSD●<OUTPUT_D> )CrLf
Explanation: There are four DVI sinks connected to ports 2, 9, 11 and 12, nothing else.
Legend: <OUTPUT_D> may contain 9, 17, 33 or 80 hexadecimal numbers. Dach number represents the state
for the corresponding output port. The meaning of the responded number depends on the actual board type
for that port. The binary representation of the responded hexadecimal numbers is shown below.
Board Aype
MX-DVID-OB
MX-DVI-AP-OB
MX-DVI-AP-OB+
MX-DVI-OPA-OB, -R
MX-DVIDL-OB
MX-DVIDL-OPA-OB
MX-HDMI-OB
MX-DVI-HDCP-OB
MX-HDMI-TP-OB
MXD-HDMI-TP-OB
MX-HDMI-OPT-OB
MX-HDMI-OPT-OB-R
MX-APS-OB; -A; -S
MX-HDMI-3D-OB; -A; -S
MX-DVI-4K-OB
MX-AUDIO-OB
MX-APS2-OB-P, -AP, -SP
MX-4APS2-4HDMI-OB, -A, -S
MX-4APS2-4HDMI-OB, -A, -S
Receiver Sense: TMDS termination present in the connected device.
▪
Hotplug Detect: Hotplug signal is presented by the connected device.
▪
▪ Laser Enable: Optical transmitter is active on output.
RX detect: Communication with the optical receiver is OC.
▪
HDMI mode: The incoming signal is HDMI.
▪
▪ HDCP active: The incoming signal is encrypted.
INFO:
Both Receiver Sense and Hotplug Detect can be used to check the attached sink device.
Example
→ {:osd}
← (OSD 010000001011000000000000000000000)CrLf
3. bit (MSB) 2. bit 1. bit
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
HDMI mode HDCP active RX detect
0 0 RX detect
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
MX-FR Series Modular Matrix Frames – User's Manual
7.8.3. All Port Status
Description: Shows the actual status of all input and output ports.
Command {PS}
Response (PS●<INPUT_D>,<OUTPUT_D>)CrLf
Legend: <INPUT_D> and <OUTPUT_D> is the same as for {:ISD} and {:OSD} commands.
7.9. I/O Port Commands
7.9.1. APS and APS2 Port
0. bit (LSB)
7.9.1.1. Port Parameters and Settings
receiver sense
Supported Boards:
0
▪ MX-TPS-IB, -A, -S; MX-TPS2-IB-P, -AP, -SP
hotplug detect
MX-4TPS2-4HDMI-IB, -A, S; MX-4TPS2-4HDMI-IB-P, -AP, -SP
▪
0
MX-4TPS2-4HDMI-OB, -A, S; MX-4TPS2-4HDMI-OB-P, -AP, -SP
▪
hotplug detect
▪ MX-TPS-OB, -A, -S; MX-TPS2-OB-P, -AP, -SP
0
Description: Query or set the TPS port-related parameters. The format and the usage are the same in the
receiver sense
case of the input and output ports.
receiver sense
Querying the Parameters
1 (fixed)
receiver sense
Command {:TPS#<in/out>@<S><I/O>=?}
laser enable
Response (TPS#<in/out>@<S><I/O>=<mod>;<eth>;
laser enable
TPS link pres.
receiver sense
Explanation: The state of the 1st output is: HDBaseT mode is selected, Dthernet is enabled.
receiver sense
Setting the Parameters
0
TPS link pres.
Command {:TPS#<in/out>@<S><I/
TPS link pres.
receiver sense
Response (TPS#<in/out>@<S/A><I/O>W=<mod>;
Explanation: The TPS mode of the selected port is set to Longreach, the Dthernet setting was not changed.
The response shows the new values. Use the 'x' character to keep the actual value of a parameter.
Format
→ {ps}
← (PS 11333777001100000,010000001011000
00)CrLf
Format
→ {:tps#1@so=?}
← (TPS#1@SO=H;1;H;0;0;17161617;
<cmod>;<pwr>;<upl>;<qual>;<err>;<len>; 23222020;0;0384;38;)CrLf
<rid>;<tmp>)CrLf
Format
→ {:tps#1@so=L;x}
O>=<mod>;<eth>}
← (TPS#1@SO=L;1;H;0;0;17161617;23222020;0;
<eth>;<cmod>;<pwr>;<upl>;<qual>;<err>; 0384;38;)CrLf
<len>;<rid>;<tmp>)CrLf
95
Example (MX-FR17)
Example
Example