Commands - Quick Summary - Lightware MX-FR Series User Manual

   
7. Programmer's Reference
7.14. Commands – Quick Summary
Switching and Control Commands
Operation
Selecting the 80th Input Port
Switching an Input to an Output
Switching an Input to All Outputs
Diagonal Switching
Batch Switch Outputs
Displaying the Current Connection States of the Outputs 7.3.7
Listing the Mute/Unmute States of All Outputs
Muting a Specified Output
Unmuting a Specified Output
Disconnecting an Output
Disconnect All Outputs
Locking a Specified Output
Unlocking a Specified Output
Saving a Preset
Loading a Preset
Preset Preview
Renaming a Preset
Renaming an Input
Renaming an Output
Querying the Name of a Preset
Querying the Name of an Input
Querying the Name of an Output
Reloading the Default Preset Names
Reloading the Default Input Names
Reloading the Default Output Names
MX-FR Series Modular Matrix Frames – User's Manual
See in
Command
Section
7.3.2 {TI=<value>}
7.3.3 {<in>@<out>}
7.3.4 {<in>@O}
7.3.5 {<in>@D}
7.3.6 {<in>@<out>}{<in>@<out>}
{VC}
7.3.8 {VM}
7.3.9 {#<out>}
7.3.10 {+<out>}
7.3.11 {0@<out>}
7.3.12 {0@O}
7.3.13 {#><out>}
7.3.14 {+<<out>}
7.3.15 {$<id>}
7.3.16 {%<id>}
7.3.17 {VP#<id>=?}
7.3.18 {PNAMD#<id>= <preset_name>}
7.3.19 {INAMD#<in>=<input_name>}
7.3.20 {ONAMD#<out>= <output_name>}
7.3.21 {PNAMD#<id>=?}
7.3.22 {INAMD#<in>=?}
7.3.23 {ONAMD#<out>=?}
7.3.24 {PNAMD#<id>=!}
7.3.25 {INAMD#<id>=!}
7.3.26 {ONAMD#<id>=!}
Communication Setup Commands
Operation
Querying the IP Settings
Reloading the Default IP Settings
Setting a Dynamic IP Address (DHCP)
Querying the RS-232 Baud Rate
Changing the RS-232 Baud Rate
Querying the Control Protocol
Changing the Control Protocol
Configure Remote Alerts
Router Status Commands
Operation
Querying the Product Type
Querying the Serial Number
Querying the Firmware Version of the CPU
Querying the CPU Firmware Compile Time
Querying the Crosspoint Size
Querying the Number of the Allowed I/O Slots
Querying the Installed I/O Boards
Querying the Firmware of All Controllers'
Querying the LAN Versions
Querying the Health Status
Querying the Error List
System Commands
Operation
Restarting the Matrix
Querying the CPU Time
Setting the CPU Time
Switching the Matrix to Standby
Reloading the Factory Default Values and Settings 7.6.5
See in
Command
Section
7.4.1 {IP_CONFIG=?}
7.4.2 {IP_CONFIG=!}
7.4.3 {IP_CONFIG=D}
7.4.4 {RS232BAUD=?}
7.4.5 {RS232BAUD=<rate>}
7.4.6 {P_?}
7.4.7 {P_<protocol>}
7.4.8 {DLDVDLSDND#<p>= <0>;<1>;<2>;<3>;<4>}
See in
Command
Section
7.5.1 {I}
7.5.2 {S}
7.5.3 {F}
7.5.4 {CT}
7.5.5 {GDTSIZD}
7.5.6 {MAXSLOTS=?}
7.5.7 {IS}
7.5.8 {FC}
7.5.9 {LAN_VDR=?}
7.5.10 {ST}
7.5.11 {DLIST=?}
See in
Command
Section
7.6.1 {RST}
7.6.2 {GDTTIMD}
7.6.3 {SDTTIMD=<date>●<time>●UTC+<zone>}
7.6.4 {PWR_<state>}
{FACTORY=<f1>;<f2>;...;fx}
118