Lcd Menu Pop-Up Messages - Lightware MX-FR Series User Manual

   
4. Operation
Use the up ▲ button to the select the Test input port and the down ▼
button to select the Preview output port. The checkboxes act like the
backlight for the illuminated I/O port buttons. If the asterisk appears
next to the port name, it means that it is selected.
This menu is activated for three seconds every time when an I/O button
is pressed on the front panel. Also. this menu appears automatically
when the AUTOTAKE mode is activated. This gives quick access to the
Test input and Preview output ports without navigating to this menu.
However, if this menu is selected manually from the main menu list, it
remains active until the escape ● button is pressed.
Input #80 Menu
This menu only appears in FR80R and
FR65R frames.
Navigate to this menu in the main
menu list and press enter  or right ►
button.
The 80th port of the crosspoint can
be selected to use the Test input port
from the CPU board or the 8th port from the 10th input board.
INFO:
The 80th input port of the crosspoint is multiplexed between
the Test input port and the 8th port of the 10th input board. This
switch is independent from the crosspoint state. The selected port
(Test input or Input board #10) will be available as the 80th input on
the crosspoint switch.
Config Backup Menu
Navigate to this menu in the main
menu list and press enter  or right ►
button.
The full matrix configuration including
every port setting and DDIDs can be
saved and reloaded later.
To save the current configuration
select Save config now! and press enter
 or right ► button. A confirmation
message appears then the progress
starts. A status indicator shows
the progress. This may take up to 1
minute. After the saving finished a
message appears: 'Ready! 20160803-
1411.cfg'
The configuration file name includes the date and time when the
configuration
YYYYMMDD-HHMM
example, the file 20160803-1411.cfg
was saved at 14:11 on 3rd August,
2016.
To reload
configuration go to Config to load item
with the up ▲ and down ▼ buttons and
then select the desired configuration
file with the left ◄ and right ► buttons.
Press enter  to reload the selected
configuration. Please note this will
~Input #80 >>
change every setting in the matrix
(I/O
Input #80
presets, DDIDs, etc.) and the previous
<Test input >
state could be restored only if the
configuration was saved earlier.
A confirmation message appears then the progress can be started.
This may take several minutes. A status indicator shows the progress.
After the configuration reloading finished a message appears: 'Ready!'
and the matrix reboots.
AAAENAIONG!

configuration reload process! If the power goes off then the matrix
will restart with factory default settings.
4.7.3. LCD Menu Pop-up Messages
ALERA Screen
~Config backup >>
This pup-up screen appears when a
high-level error occurs in the matrix.
Press the enter  button to dismiss this
alert and jump to the system log entry.
Config backup
Use the up ▲ and down ▼ buttons to
~Save config now! >>
scroll between the log entries. Please
Config to load:
contact support@lightware.com.
20160803-1411
Saving config!
14% ready
MX-FR Series Modular Matrix Frames – User's Manual
was saved in
Config backup
format. For
Save config now!
~Config to load:
~< 20160901-1051
a previously saved
Load config file?
NO
~YES
Loading - 82%
Don't turn off!
port parameters, crosspoint
The matrix must not be switched off during a
~------------------~
!ALERT!
!FANSPEED
~------------------~
Log entries
7/8 Error
FANSPEED
p:0x01 o:3
~
>~
>>
!
!
47