Specifications - Navistar INTERNATIONAL DT 466 Service Manual

276
Specifications
Table 37 Crankshaft Specifications
Type
Main Bearing journal diameter
Standard size
0.254 mm (0.010 in) undersized
0.508 mm (0.020 in) undersized
0.762 mm (0.030 in) undersized
Damper mounting area runout (maximum)
Flywheel mounting surface runout (maximum)
Main bearing journal maximum out-of-round
Main bearing journal taper (maximum per inch)
Main bearing thrust face runout (TIR maximum)
Main bearing width (except rear thrust)
Number of main bearings
Rear oil seal journal runout (maximum)
Thrust taken by
Thrust bearing journal length
Connecting rod journal diameter
Standard Size
0.0254 mm (0.010 in) undersized
0.508 mm (0.020 in) undersized
0.762 mm (0.030 in) undersized
Center line of main bearing bore to head deck
Connecting rod bearing to crankshaft running
clearance
Connecting rod bearing width
Connecting rod journal maximum out-of-round
Connecting rod journal taper (maximum per inch)
Crankshaft end play
Crankshaft end play maximum wear limit
Crankshaft flange outside diameter
Crankshaft gear backlash
Main bearing to crankshaft running clearance
Connecting rod to crankshaft side clearance
Standard size to 0.51 mm (0.020 in) undersized
Read all safety instructions in the "Safety Information" section of this manual before doing any procedures.
CRANKCASE, CRANKSHAFT, AND CAMSHAFT
Follow all warnings, cautions, and notes.
© 2009 Navistar, Inc.
Steel forged, induction hardened, grindable
107.95 ± 0.015 mm (4.250 ± 0.0006 in)
107.70 ± 0.015 mm (4.240 ± 0.0006 in)
107.44 ± 0.0152 mm (4.230 ± 0.0006 in)
107.19 ± 0.0152 mm (4.220 ± 0.0006 in)
0.03 mm (0.001 in)
0.05 mm (0.002 in)
0.05 mm (0.002 in)
0.071 mm (0.0028 in)
0.03 mm (0.001 in)
34.19 ± 0.13 mm (1.346 ± 0.005 in)
7
0.08 mm (0.003 in)
No. 7 rear upper main bearing
34.404 ± 0.038 mm (1.3545 ± 0.0015 in)
80.0 ± 0.0152 mm (3.1500 ± 0.0006 in)
79.7 ± 0.0152 mm (3.1400 ± 0.0006 in)
79.5 ± 0.0152 mm (3.1300 ± 0.0006 in)
79.2 ± 0.0152 mm (3.1200 ± 0.0006 in)
368.3 ± 0.05 mm (14.50 ± 0.002 in)
0.030 - 0.107 mm (0.0012 - 0.0042 in)
40.01 mm (1.575 in)
0.0064 mm (0.00025 in)
0.0069 mm (0.00027 in)
0.15-0.31 mm (0.006 - 0.012 in)
0.51 mm (0.020 in)
155.58 mm (6.125 in)
0.08-0.41 mm (0.003 - 0.016 in)
0.046 - 0.127 mm (0.0018 - 0.0050 in)
0.30 ± 0.11 mm (0.012 ± 0.005 in)
34.404 ± 0.03 mm (1.3545 ± 0.010 in)
EGES-265-2