GE Power Quality Meter Series Instruction Manual page 243

8 DNP COMMUNICATIONS
Table 8–1: POINT LIST FOR ANALOG INPUT/OUTPUT CHANGE (Sheet 5 of 5)
POINT MOBUS DESCRIPTION
REG
137 0487 Voltage Vbn THD - Maximum
138 0488 Voltage Vcn THD - Maximum
139 0489 Voltage Vab THD - Maximum
140 048A Voltage Vbc THD - Maximum
141 048B Voltage Vca THD - Maximum
142 04C8 ADC Reference
143 04C9 Power Loss Fine Time
144 04CA Power Loss Coarse Time
145 04CB Current Key Press
146 04CC Internal Fault Error Code
147 0000 Multilin Product Device Code
148 0001 Hardware Version Code
149 0002 Main Software Version Code
150 0003 Modification File Number 1
151 0004 Boot Software Version Code
152 0005 Supervisor Processor Version Code
153 0007 Modification File Number 2
154 0008 Modification File Number 3
155 0009 Modification File Number 4
156 000A Modification File Number 5
157 0020 Serial Number Character 1 and 2
158 0021 Serial Number Character 3 and 4
159 0022 Serial Number Character 5 and 6
160 0023 Serial Number Character 7 and 8
161 0030 Manufacture Month/Day
162 0031 Manufacture Year
163 0032 Calibration Month/Day
164 0033 Calibration Year
see footnote explanations at the end of the table
1. This point is used to reconstruct neutral current values from the 1,000ths per-unit quantities given in the other points.
Multiply the particular point by this one, and divide by 1000 to get amps.
2. The VT Ratio setpoint is always reported, but is not used if a direct (i.e., without VTs) voltage wiring scheme is config-
ured. In this case the VT Ratio setpoint is ignored, and a ratio of 1.0:1 is used in the PQM.
3. This point is used to reconstruct voltage values from the 1,000ths per-unit quantities given in the other points. Multiply
the particular point by this one, and divide by 1000 to get volts. Since some SCADA systems don't read 32 bit values,
you can also multiply the VT ratio and nominal secondary (both of which are 16 bit) in the master in cases where the
nominal primary may exceed 32767 volts.
4. This point is used to reconstruct power values from the 1,000ths per-unit quantities given in the other points. Multiply
the particular point by this one, and divide by 1000 to get VA, kW or kvar.
5. In Modbus, the current keypress is reported with format code F6. In order to fit the value into a sixteen-bit signed
value, F8 is used in DNP, with ASCII zero (49 decimal) returned when no key is pressed.
GE Power Management
UNIT / VALUE
0.1 x %
0.1 x %
0.1 x %
0.1 x %
0.1 x %
-
10 ms
0.1 min.
-
-
always 65
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PQM Power Quality Meter
8.1 DNP 3.0 PROTOCOL
DEADBAND FORMAT EVENT CLASS
CODE ASSIGNED TO
1 unit F1
1 unit F1
1 unit F1
1 unit F1
1 unit F1
20 units F1
1 unit F1
1 unit F1
5
1 unit F8
1 unit F108
- F1
- F5
- F1
- F1
- F1
- F1
- F1
- F1
- F1
- F1
- F10
- F10
- F10
- F10
- F24
- F25
- F24
- F25
3
3
3
3
3
2
2
2
2
2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8
8-13