Table of Contents
Advertisement
Programming
3.1.20 Parameter Group 0-** Operation/
Display
001
Language
Value:
3
3
English (ENGLISH)
German (DEUTSCH)
French (FRANCAIS)
Danish (DANSK)
Spanish (ESPAÑOL)
Italian (ITALIANO)
State when delivered may vary from factory setting.
Function:
The choice in this parameter defines the language to be
used on the display.
Description of choice:
There is a choice of [0] English, [1] German, [2] French, [3]
Danish, [4] Spanish and [5] Italian.
002
Local/remote control
Value:
Remote control (REMOTE)
Local control (LOCAL)
Function:
There is a choice of two methods of controlling the FC
motor:[0] Remote control and [1] Local control.
Description of choice:
If [0] Remote control is selected, the FC motor can be
controlled via:
1.
The control terminals or the serial communication
port .
2.
The [Start] key. However, this cannot overrule
Stop commands (also start-disable) entered via
the digital inputs or the serial communication
port.
3.
The [Stop], [Jog] and [Reset] keys, provided that
these are active (see parameters 014, 015 and
017).
If [1] Local control is selected, the FC motor can be
controlled via:
1.
The [Start] key. However, this cannot override
Stop commands on the digital terminals (if [2] or
[4] has been selected in parameter 013).
2.
The [Stop], [Jog] and [Reset] keys, provided that
these are active (see parameters 014, 015 and
017).
3.
The [FWD/REV] key, provided that this has been
activated in parameter 016 and that in parameter
013 a choice of [1] or [3] has been made.
36
®
VLT
DriveMotor FCM Series
4.
003
Value:
[0]
Par 013 set for [1] or [2]:
[1]
0 - f
[2]
Par 013 set for [3] or [4] and par. 203 = [0]
[3]
set for:
[4]
Ref
[5]
Par 013 set for [3] or [4] and par. 203 = [1]
set for:
-Ref
Function:
This parameter allows manual setting of the desired
reference value (speed or reference for the selected config-
uration, depending on the choice made in parameter 013).
The unit follows the configuration selected in parameter
100, provided that [3] Process regulation, closed loop has
been selected.
Description of choice:
[1] Local must be selected in parameter 002 for this
[0]
parameter to be used.
[1]
The set value is saved in the case of a voltage dropout, see
parameter 019.
In this parameter Data Change Mode is not exited
automatically (after time out).
Local reference cannot be set via the serial communication
port.
004
Value:
Factory Setup (FACTORY SETUP)
Setup 1 (SETUP 1)
Setup 2 (SETUP 2)
Multi Setup (MULTI SETUP)
Function:
The choice in this parameter defines the Setup number
you want to control the functions of the FC motor.
All parameters can be programmed in two individual
parameter Setups, Setup 1 and Setup 2. In addition, there
is a pre-programmed Setup, called Factory Setup, that
cannot be modified.
Description of choice:
[0] Factory Setup contains the factory data. Can be used as
a data source if the other Setups are to be returned to a
known state.
Parameters 005 and 006 allow copying from one Setup to
the other.
[1] Setups 1 and [2] 2 are two individual Setups that can be
selected as required.
[5] Multi-Setup is used if remote-mounting switching
between Set-ups is desired. Terminals 2, 3, 4, and 5 as well
®
MG03BA02 - VLT
is a registered Danfoss trademark
Via parameter 003 the local reference can be
controlled by means of the "Arrow up" and
"Arrow down" keys.
Local reference
MAX
- Ref
MIN
MAX
- + Ref
MAX
MAX
Active Setup
000.000
000.000
000.000
[0]
[1]
[2]
[5]
Advertisement
Table of Contents
