Table of Contents - High Speed Compact Disc TABLE OF CONTENTS Manufacturer’s Statement: For technical reasons, Buhler Industries Inc. reserves the right to modify machinery design and specifications provided herein without any preliminary notice. Information provided herein is of descriptive nature. Performance quality may depend on ground type, applied techniques, weather conditions and INTRODUCTION .
Page 4
Table of Contents - High Speed Compact Disc...
Page 5
Date: Customer / Owner’s Signature: Remove this Warranty Registration Form from the Operator’s Manual. Make two copies of the form. Send original Warranty Registration Form to Farm King. Give one copy to the customer and one copy to the dealer.
Page 6
Warranty Registration - High Speed Compact Disc...
Page 7
Pre - Delivery Checklist - High Speed Compact Disc PRE - DELIVERY CHECKLIST 01-Inoperative 02-Improper Adj. 03-Def. Fasteners 04-Interference 05-Damage 06-Missing 07-Leak 08-Dry 09-Poor fit 10-High 11-Low 12-High torque 13-Low torque 14-Other Description Def. Rep. Problem - Corrective Action Overall Machine Operator’s Manual Decals and safety reflectors Wheels, tires and pressures...
Page 8
Pre - Delivery Checklist - High Speed Compact Disc 01-Inoperative 02-Improper Adj. 03-Def. Fasteners 04-Interference 05-Damage 06-Missing 07-Leak 08-Dry 09-Poor fit 10-High 11-Low 12-High torque 13-Low torque 14-Other Description Def. Rep. Problem - Corrective Action Other Complete the “Delivery Report” Dealership Sales to Complete with Customer Complete warranty form with customer Review “First 400 Acres”...
Page 9
Farm King equipment. READ AND UNDERSTAND THIS OPERATOR AND PARTS MANUAL BEFORE OPERATING YOUR FARM KING EQUIPMENT. If you have any questions, see your Farm King dealer. This manual may illustrate options and accessories not installed on your Farm King equipment.
Page 11
Introduction - High Speed Compact Disc Serial Number Location OWNER’S INFORMATION Thank you for your decision to purchase a Farm King Please enter the model and serial number in the space High Speed Compact Disc (HSCD). To ensure provided for easy reference.
It may also be used to alert against Understand the Written Instructions, Rules and unsafe practices. Regulations • The written instructions from Farm King include the Warranty Registration, Dealer Inspection Report, Operator’s manual and equipment signs (decals). •...
Safety - High Speed Compact Disc SAFETY INSTRUCTIONS (CONT’D) • Always stay clear of the folding wings when they are being raised, lowered or placed in or out of the Use Safety Rules folded position. • Read and follow instructions in this manual and the •...
Safety - High Speed Compact Disc Tractor Requirements And Capabilities • The parking brake shall be engaged before leaving the operator’s seat. Rollaway can occur because • Fasten seat belt securely. Tractor must be transmission prevent tractor equipped with a roll-over protective structure movement.
Fueling Operation The Farm King equipment must be in good operating condition before use. Check all of the items listed on the service schedule under daily checks (see SERVICE SCHEDULE on page Stop the engine and let it cool before adding fuel. No 95).
Safety - High Speed Compact Disc FIRE PREVENTION (CONT’D) Welding And Grinding Always clean the tractor and equipment, disconnect the battery, and disconnect the wiring from the equipment controls before welding. Cover rubber hoses, battery and all other flammable parts. Keep a fire extinguisher near the equipment when welding.
DECALS Follow the instructions on all the Decals that are on the equipment. Replace any damaged decals and be sure they are in the correct locations. Decals are available from your Farm King dealer. Decal Locations (Top and Rear Views)
Page 21
Safety - High Speed Compact Disc Location A - A (Hitch - Both Sides) Figure 5 88717373 A-A P/N EZDF10061 (Amber) P/N 88719822 P/N 88719472 P/N 88719471 P/N 88719470 P/N 88719469...
Page 22
Safety - High Speed Compact Disc Location B (Hitch - Top) Figure 6 P/N EZDF13001 86054197 P/N 86054197 86054092 P/N 86054092 88717373 B - B 86058185 P/N 86058185...
Page 23
Safety - High Speed Compact Disc Location C - C (Hitch - Both Sides) Figure 7 88717373 C - C DANGER TO AVOID PERSONAL INJURY OR DEATH, ALWAYS STAND CLEAR WHEN WINGS ARE BEING RAISED, LOWERED OR IN FOLDED POSITION. WINGS MAY FALL RAPIDLY, CAUSING BODILY INJURY IF HYDRAULIC SYSTEM FAILED OR IF HYDRAULIC LEVER IS ACCIDENTLY OPERATED.
Page 24
Safety - High Speed Compact Disc Location C - C (Hitch - Both Sides) (Cont’d) Figure 8 88717373 C - C P/N 88718824 86054197 P/N 86054197 86058185 86054092 P/N 86058185 P/N 86054092 P/N EZA75759 P/N EZDF10061 (Amber)
Page 25
Safety - High Speed Compact Disc Location D - D (Hitch - Light Bracket) Figure 9 P/N 105420 88717373 D -D Location E - E (Hitch - Light Bracket) Figure 10 P/N EZDF10061 (Amber) 88717373 E - E...
Page 26
Safety - High Speed Compact Disc Location F - F (Wings) Figure 11 88717373 F -F DANGER TO AVOID PERSONAL INJURY OR DEATH, ALWAYS STAND CLEAR WHEN WINGS ARE BEING RAISED, LOWERED OR IN FOLDED POSITION. WINGS MAY FALL RAPIDLY, CAUSING BODILY INJURY IF HYDRAULIC SYSTEM FAILED OR IF HYDRAULIC LEVER IS ACCIDENTLY OPERATED.
OPERATION a standard practice for all of your equipment. An untrained operator is unqualified to operate this equipment. The following sign-off sheet is provided for your record and to show that all personnel operating your Farm King equipment, have taken time to read and understand this manual to ensure best performance and longevity of this equipment.
Farm King Dealer. • Be aware of overhead power lines. Assemble the equipment in the following order: • Keep away from power lines when unloading and assembling the equipment.
Assembly - High Speed Compact Disc BASE GROUP NOTE: The following images throughout assembly section of this manual may not Center Frame and Wings Assembly show your exact model components as they appear but the procedure is correct. Assemble the center frame and wings on a flat level surface.
Page 33
Assembly - High Speed Compact Disc Figure 13 Figure 15 1 1 1 FRONT B-17004 B-17001B 4. Install washers (1, Figure 15) (as required) between 1. Connect straps to LH wing frame (1,Figure 13) and to the center frame mount (2) and the LH wing mount an approved lifting device.
Assembly - High Speed Compact Disc Figure 17 Figure 19 FRONT FRONT B-17010 B-17008 1. Connect straps to RH wing frame (1, Figure 19) and 6. Install the bushing (1, Figure 17) washer (2), 5/8" x 2" to an approved lifting device. bolt (3) through the mounting pin on the front and rear mount.
Page 35
Assembly - High Speed Compact Disc Figure 21 Figure 23 B-17010A B-17023A 5. Raise the hitch frame and align the hitch frame holes 9. Install the 5/8” lock nut on the 5/8” x 2” bolt (1, Figure with the holes on the center frame. 23) and tighten.
Assembly - High Speed Compact Disc Installing Hydraulic Cylinders Figure 27 Figure 25 B-17016 B-17128 1. Install the center attachment 3-1/2" x 8" hydraulic cylinder (1, Figure 27) (base end) to the cylinder If not already installed, hardened bushings (1, Figure 25) mount at the rear of the center frame (2).
Page 37
Assembly - High Speed Compact Disc Figure 29 Figure 31 REAR LH WING B-17106 FRONT B-17017 NOTE: The LH attachment hydraulic cylinder with depth stop mount (1, Figure 29). 1. Install the wing rockshaft 3-1/2" x 8" hydraulic cylinder (1, Figure 31) (base end) to the cylinder mount (2) on 1.
Assembly - High Speed Compact Disc Figure 33 Installing The Hydraulic Jack, Wing Cradle and Hitch Figure 35 B-17034 3. Raise the rod ends of the center frame fold cylinders B-17047 (1, Figure 33). 1. Insert the base end of the cylinder (1, Figure 35) up 4.
Page 39
Assembly - High Speed Compact Disc Figure 37 2. Install four 3/8" x 1-1/2" bolts (2) and flat washers through the pad and mount. 3. Install lock 3/8" washers, 3/8" nuts on each bolt and tighten. Repeat procedure for the LH wing stop. Figure 39 FOUR MOUNT...
Assembly - High Speed Compact Disc Figure 40 3. Place strap (4) as shown and install a bolt (5) through the mount and strap (both sides) 4. Attach a lifting device to the straps. Figure 42 B-17039 1. Place the pintle hitch (1, Figure 40) at the desired height (see Pintle Hitch Adjustment on page 80).
Assembly - High Speed Compact Disc Figure 43 Figure 45 B-17027 B-17028 8. At the rear of the rockshaft install the four smaller 13. With straps and approved lifting device rotate the rock bearing castings (1, Figure 43) onto the bearing shaft up and place a support stand (1, Figure 45) liners.
Assembly - High Speed Compact Disc Figure 47 3. Raise the center frame rear tube up and align the mounting holes to the center frame mount holes. 4. Install three 3/4" x 2-1/2" bolts (3) down through the center frame mount. Install 3/4” flat washers (4) and 3/4"...
Assembly - High Speed Compact Disc Figure 50 7. Tighten the four bolts on each mounting tube mount. Repeat procedures Figure 50 and Figure 51 for the LH wing rear tube. Disc Arm / Blade Assembly Blade spacing on front and rear rows is 254 mm (10"), with rear blades offset to front blades by 127 mm (5").
Page 44
Assembly - High Speed Compact Disc Figure 53 Figure 55 REAR FRONT B-17057 B-17064 The LH rear disc arm (1, Figure 53) has three slots (2) 1. Raise the disc blade arm (1, Figure 55) with slots up and is the only disc blade arm that will have slots. to the mounting tube and install two rubber inserts (2) as shown.
Page 45
Assembly - High Speed Compact Disc Figure 57 Figure 59 B-17061 B-17063 NOTE: The procedure shown is only for the slotted NOTE: Rear disc blade installation should be disc arm, located on the outer rear of the LH preformed working from left side to right side wing.
Assembly - High Speed Compact Disc End Shield Assembly Figure 63 Figure 61 B-17087 B-17087 3. Raise the end shield leg (1, Figure 63) up to the end shield tube and install two rubber inserts (2). End shield leg (1, Figure 61) and mount bracket (2) is installed on the LH outer wing.
Assembly - High Speed Compact Disc Installing Wing Rockshafts 6. On the backside of the bearing casting, install a 3/4" x 7" bolt (2) up through the bottom of the bearing Figure 65 castings (both sides). 7. Install 3/4" lock washers (3) and 3/4" nuts (4) at the top of each bearing mount (both sides).
Assembly - High Speed Compact Disc Figure 68 Installing The Attachment Rockshafts and Cage Rollers Figure 70 B-17095 1. Install the hub / spindle (1, Figure 68) assembly into the rockshaft. B-17081 2. Align the bolt hole and install the 1/2" x 5-1/2" bolt (2) 1.
Page 49
Assembly - High Speed Compact Disc 4. Raise the rockshaft slowly aligning the bolts with the Figure 73 bearings until the two bearing castings fully contact the rockshaft bearing mounts. Figure 72 B-17073 1. With straps and proper lifting device raise the cage roller arm (1, Figure 73) up and align with the B-17112 attachment rockshaft mount as shown.
Page 50
Assembly - High Speed Compact Disc Figure 75 Figure 77 B-17113 B-17114 1. Apply a light coat of ant-seize to the shaft on the cage 1. Install a strap and proper lifting device to the cage roller. Install the bearing (1, Figure 75) both sides. roller (1, Figure 77).
Page 51
Assembly - High Speed Compact Disc Figure 79 Figure 81 B-17114 B-17114 5. Tighten the four bolts (1, Figure 79) both sides. 8. Install a strap and proper lifting device to the cage roller (1, Figure 81). Figure 80 9. Install a strap and proper lifting device to the cage roller arm (2).
Page 52
Assembly - High Speed Compact Disc Figure 83 Figure 85 B-17114 B-17137 14. Reinstall the bearing / arm assembly (1, Figure 83) 1. With a strap and proper lifting device attached to the aligning the cage roller shaft into the bearing and cage roller, raise the cage roller and align with the rod aligning the cage roller arm (2).
Assembly - High Speed Compact Disc Hydraulics Figure 87 NOTE: See HYDRAULIC CONNECTION SPECIFICATIONS on page 165 for correct procedures for installing and tightening hydraulic fittings and hoses. Figure 86 FRONT B-17038 5. Install and tighten the six straight fittings (1, Figure REAR 87) on the front side of the hydraulic valve.
Page 54
Assembly - High Speed Compact Disc Figure 89 • Center Frame Fold Circuit (Red Tie). • Rockshaft Lift Circuit (Green Tie). • Wing Fold Circuit (Blue Tie) Figure 91 B-17144 1. Install and tighten the six straight fittings (1, Figure 89) into the end of each valve (2).
Page 55
Assembly - High Speed Compact Disc Figure 93 Figure 95 B-17045 B-17158 1. Install the 90° elbow (1, Figure 93) into the jack 1. Install the 90° elbow (1, Figure 95) into the rod end on cylinder base end and tighten. the RH center frame fold cylinder and tighten.
Page 56
Assembly - High Speed Compact Disc Figure 97 5. Connect hoses (6, 7 and 8) and tighten. Figure 99 B-17137 1. Install the 90° elbows (1, Figure 97) to the RH rear B-17172 wing attachment cylinder and tighten. 6. Install the 90° elbow (1, Figure 99) on the rod end of 2.
Page 57
Assembly - High Speed Compact Disc Figure 101 Figure 103 B-17155 1. Install the 90° elbows (1, Figure 103) on the LH wing B-17147 rockshaft cylinder and tighten. 1. Install the 90° elbows (1, Figure 101) to the LH rear 2.
Page 58
Assembly - High Speed Compact Disc Figure 105 Figure 107 B-17156 B-17134 1. Install the straight fittings (1, Figure 105) on the RH 1. Connect hoses (1 - 7, Figure 107) and tighten. hitch frame rockshaft cylinder and tighten. Figure 108 2.
Assembly - High Speed Compact Disc Figure 109 Figure 111 B-17040 B-17043 1. Place the hose bracket (1, Figure 109) as shown over 1. Install a 1/2" nut (1, Figure 111) onto each side of the the mounting brackets on the hitch frame. Install two u-bolt (2), thread the nuts fully onto the u-bolt.
Assembly - High Speed Compact Disc 3. Install the quick release pin (5) through the depth stop Figure 114 plates and cylinder stop plate mount. 4. Repeat procedure for LH hitch frame rockshaft depth stop plates and for the LH rear attachment depth stop plates on the rear LH wing.
Page 61
Assembly - High Speed Compact Disc Figure 115 Figure 116 B-17135 B-17145 1. Remove the bolts from the two weld nut locations on 1. Remove the bolts from the weld nut locations on the the top LH hitch frame and discard bolts. hitch frame and discard bolts.
Page 62
Assembly - High Speed Compact Disc Figure 118 Figure 120 B-17148 B-17131 1. Install the rubber hose guard (1, Figure 118) near the 1. Install two rubber hose guards (1, Figure 120) near base end of the LH center frame fold cylinder as the base end of the LH wing fold cylinder as shown.
Assembly - High Speed Compact Disc Light Installation 3. Install the amber light (3) into the slot on the bracket and secure with flat washer, lock washer and nut (4). NOTE: The tractor controls operate the required Tighten nut. flashing, turn and brake light requirements. 4.
Page 64
Assembly - High Speed Compact Disc Figure 124 4. Route the light wire harness (6) along the hydraulic hoses, through the front of the hose holder. 5. Install the light harness 7-pin connector (7) into the electrical storage plug. B-17142 1.
Assembly - High Speed Compact Disc Wing and Center Frame Fold Cylinders Figure 129 To connect the rod ends of the wing and center frame fold cylinders, connect the tractor to the equipment hitch. See INITIAL SET-UP on page 80 and see Connecting The Equipment To The Tractor on page 81.
Assembly - High Speed Compact Disc Hydraulic Jack Hose Identification Figure 131 YELLOW TIE STRAP TO TRACTOR YELLOW TIE STRAP ITEM DESCRIPTION HOSE ROUTING 130" HOSE ASSY From tractor to lock-up valve (yellow tie) 156" HOSE ASSY From tractor to jack cylinder (base end) (yellow tie) 19"...
Operation - High Speed Compact Disc GENERAL INFORMATION 2. Check the equipment for damaged or loose components and hardware. Replace damaged Pre - Operation Checklist components (if required) and tighten all hardware before operating the equipment (see SERVICE Before operating the equipment for the first time and SCHEDULE on page 95).
4. Check that tires are inflated to 317 kpa (46 psi). The HS8525 and HS8530 will require a tractor with minimum 335 to 425 HP. 5. Check that wheel nuts and bolts are torqued to: The HS8535 will require a tractor with minimum 390 203.3...
Operation - High Speed Compact Disc Drawbar Entering And Leaving The Operator’s Position NOTE: Tractor must be equipped with a clevis type drawbar to pull the equipment. Figure 136 Follow the instructions in your tractor’s operation manual for the correct procedure. Entering The Operator’s Position Move to the operator’s position, start the engine and release the parking brake.
Operation - High Speed Compact Disc INITIAL SET-UP Pintle Hitch Adjustment NOTE: Tractor must be equipped with a clevis type drawbar to pull the equipment. With tractor parked on level ground, measure the distance between the ground and the top side of tractor drawbar. Figure 137 25 - 30 FT MACHINE PINTLE POSITION 35 FT - 40 FT MACHINE PINTLE POSITION...
Operation - High Speed Compact Disc Connecting The Equipment To The Tractor If the equipment hitch height needs to be adjusted, stop the tractor when drawbar is about 127 mm (5”) in front of the equipment pintle hitch. 4. Leave the operator’s position (see Leaving The Operator’s Position on page 79).
Page 82
Operation - High Speed Compact Disc NOTE: Always use a safety chain with a strength rating greater than the gross weight of the towed equipment. 14. Enter the operator’s position (see Entering The Operator’s Position on page 79). 15. Use the tractor’s hydraulics to raise hydraulic jack to the storage position.
Operation - High Speed Compact Disc Hydraulic Lines To Connect: Figure 141 HIGH PRESSURE FLUID HAZARD To prevent serious injury or death from high pressure fluid: • Relieve pressure on system before repairing or B-17192 adjusting. • Wear proper hand and eye protection when 1.
Operation - High Speed Compact Disc Connect Electrical Harness Folding And Unfolding Wings Figure 142 ELECTROCUTION HAZARD To prevent serious injury or death from electrocution: • Be aware of overhead / underground powerlines. • Keep away from powerlines when transporting or folding / unfolding wings.
Page 85
Operation - High Speed Compact Disc Unfolding: Transport to Field Position 6. Use the tractor’s hydraulic controls to ensure the center frame lift cylinders are fully extended. See 1. Move to the operator’s position, start the engine the tractor’s owner’s manual. and release the parking brake (see Entering The Operator’s Position on page 79).
Page 86
Operation - High Speed Compact Disc Folding: Field Position to Transport Figure 146 Wing and center frame fold cylinder hydraulic controls should be in float from field operation. 1. Fully lift the frame out of the ground by fully extending and phasing out hitch frame rockshaft lift cylinders.
Operation - High Speed Compact Disc Setting Tillage Depth Figure 149 1. Fully lift the equipment frame by fully extending and re-phasing the frame lift cylinders. NOTE: Re-phase lift cylinders at the start of each work day (see Rephasing Rockshaft Cylinders on page 90).
Operation - High Speed Compact Disc Setting End Shield and LH Rear Blade Figure 151 The LH end shield and adjustable LH rear blade are designed to eliminate any trench that may be caused by the rear LH end blade. The end blade on the LH rear row of blades cuts the soil and throws the soil towards the center of the disc, which may leave a trench depending on soil type.
Operation - High Speed Compact Disc OPERATING THE EQUIPMENT Field Operation 1. Move to the operator’s position, start the engine and release the parking brake (see Entering The Operator’s Position on page 79). AVOID SEVERE EQUIPMENT DAMAGE 2. Move the tractor / equipment to the starting point When operating the equipment: of the work area.
Operation - High Speed Compact Disc Recommended operating speed is 13 - 19 kph (8 - 12 mph). 8. Move tractor and equipment forward, lower equipment into the ground until the rockshaft cylinders make contact with the stops and the equipment reaches desired tilling depth.
Maintenance - High Speed Compact Disc TROUBLESHOOTING General Chart Instructions are necessary before operating or servicing equipment. Read and understand the Operator’s Manual and safety signs (decals) on equipment. Follow warnings and instructions in the manuals when making repairs, adjustments or servicing. Check for correct function after adjustments, repairs or service.
Page 94
Maintenance - High Speed Compact Disc PROBLEM CAUSE CORRECTION Hydraulics system is going over Incorrect Hydraulic manifold installed. Ensure correct manifold installed for pressure relief setting. Excessive weight added or built up on machine. Remove added weight or machine. excessive debris build up. Excessive frame lift or frame fold time.
Maintenance - High Speed Compact Disc SERVICE SCHEDULE BLADES Maintenance Intervals Blade Arm / Blade / Bearing Inspection Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures. The service schedule is a guide for correct maintenance of the equipment.
Maintenance - High Speed Compact Disc WHEEL / TIRE REPLACEMENT CHECK WHEEL BOLTS AFTER: AVOID INJURY OR DEATH 1. First five hours of field operation. • Always chock tires before performing any 2. First twenty-five hours of field operation. maintenance or service. 3.
Maintenance - High Speed Compact Disc Tire Pressure HYDRAULIC MAINTENANCE Hydraulic Hose Requirements Do not exceed the 3000 psi rated maximum operating pressure. When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to Table 2 one side and NOT in front of or over the tire assembly.
Maintenance - High Speed Compact Disc LUBRICATION Figure 157 Recommendations Always use a good quality multi-purpose/ lithium base grease when lubricating the equipment. • Always use a hand-held grease gun. • Clean fitting before greasing, to avoid injecting dirt and grit. •...
Maintenance - High Speed Compact Disc CLEANING Fully Clean the equipment EVERY 50 HOURS: Keep the equipment free of any debris. SAFETY SIGN (DECAL) INSTALLATION Procedure When replacing safety signs (decals), temperature must be above 10° C (50° F). • Remove all portions of the damaged safety sign (decal).
Maintenance - High Speed Compact Disc STORAGE AND RETURN TO SERVICE • Set planks under each wheel. • Relieve pressure in all hydraulic cylinders. Storage • Disconnect hydraulic hoses from tractor and cap. Sometimes it may be necessary to store your equipment •...
Part Identification - High Speed Compact Disc GENERAL INFORMATION The parts identification section lists descriptions, part numbers and quantities for the Farm King High Speed Compact Disc. Contact your Farm King dealer for additional part information. WHEELS / TIRES HITCH...
Part Identification - High Speed Compact Disc HITCH - 25’, 30’ 19 23 27 DETAIL A SECTION B-B 21 24 28 SECTION E-E DETAIL C SECTION G-G SECTION D-D 88718145...
Page 107
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 132757 LINCH PIN 7/16 EZB037040 BOLT HEX 3/8 NC X 4 816357 PIN WELD'T TSL 1.25 X 7.375 86518307 PIN - HAIR COTTER, 0.125X2.563 IN 88713573 WASHER - THRUST WB 88713643 BUSHING-WALKING BEAM PIVOT 88715619...
Page 108
Part Identification - High Speed Compact Disc HITCH - 25’, 30’ CONTINUED 19 23 27 DETAIL A SECTION B-B 21 24 28 SECTION E-E DETAIL C SECTION G-G SECTION D-D 88718145...
Page 109
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION EZBN037 NUT 3/8 UNC 86557158 ANTI SEIZE PER 86557157 86050059 STD GREASE - LITHIUM...
Part Identification - High Speed Compact Disc HITCH - 35’, 40’ 19 23 27 DETAIL A SECTION B-B 21 24 28 DETAIL C SECTION D-D 20 35 SECTION E-E SECTION G-G 88717982...
Page 111
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 132757 LINCH PIN 7/16 EZB037040 BOLT HEX 3/8 NC X 4 816357 PIN WELD'T TSL 1.25 X 7.375 86518307 PIN - HAIR COTTER, 0.125X2.563 IN 88661392 HITCH, PINTLE; CAT. 4-5 CRSSOVR 88713573 WASHER - THRUST WB 88713643...
Page 112
Part Identification - High Speed Compact Disc HITCH - 35’, 40’ CONTINUED 19 23 27 DETAIL A SECTION B-B 21 24 28 DETAIL C SECTION D-D 20 35 SECTION E-E SECTION G-G 88717982...
Page 113
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION EZBN037 NUT 3/8 UNC 86557158 ANTI SEIZE PER 86557157 86050059 STD GREASE - LITHIUM...
Part Identification - High Speed Compact Disc FRAME CENTER SECTION A-A 88717967...
Page 115
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 86534279 N FL G8 P.75-10 88713643 BUSHING-WALKING BEAM PIVOT 88718468 TUBE - W.A. BLADE MTG 88717916 FRAME - W.A CENTER HSCD EZB075025 BOLT HEX 3/4NC X 2-1/2 EZDR13120 BUSHING-SPRING EZBW20081213F 2 Od X 13/16 Id X .135...
Part Identification - High Speed Compact Disc HYDRAULICS - 25’, 30’ WING LIFT / ROCKSHAFT 88719870...
Page 135
Part Identification - High Speed Compact Disc WING LIFT RIGHT WING LEFT WING DETAIL B DETAIL A 66 2 DETAIL C DETAIL D 88719870...
Page 136
Part Identification - High Speed Compact Disc ROCKSHAFT RIGHT ROCKSHAFT LEFT ROCKSHAFT CYLINDER CYLINDER 74 5 74 5 74 76 74 76 DETAIL A DETAIL B 3 28 16 74 DETAIL C 88719870...
Page 137
Part Identification - High Speed Compact Disc VALVE LEFT ROCKSHAFT RIGHT ROCKSHAFT CYLINDER CYLINDER 75 69 DETAIL A DETAIL B 88719870...
Page 138
Part Identification - High Speed Compact Disc SHUT OFF VALVE DETAIL A 4 66 DETAIL B 65 33 DETAIL C DETAIL D 88719870...
Page 139
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 21193 CLAMP HOSE 14.2 29256 COVER PLATE 32383 CLAMP-HOSE #128 TYPE F 815608 BLOCK POLYPROPELENE 3/8 PAIR 816357 PIN WELD'T TSL 1.25 X 7.375 86018376 ELBOW 90 DEGREE 86044739 HOSE CLAMP - INSULATED, 0.68"...
Page 140
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 88717816 HOSE [-06, 06-00, 06-90, 29] 88717827 HOSE [-06, 06-00, 06-90, 26] 88717828 HOSE [-06, 06-00, 06-90, 103] 88717831 TUBE, DEPTH STOP SUPPORT 88717864 ABRASIVE HOSE SLEEVE, NYLON, HSCD 88717873 TIE-HYD, FRAME FOLD, RED 88717874...
Page 141
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION EZBP37250 COTTER PIN-3/8X2-1/2" EZBW037L WASHER LOCK 3/8 X 11/16 X 3/32 EZDR5262 PIN-CYLINDER...
Part Identification - High Speed Compact Disc HYDRAULICS - 35’, 40’ WING LIFT / ROCKSHAFT 88718976...
Page 143
Part Identification - High Speed Compact Disc WING LIFT RIGHT WING LEFT WING DETAIL B DETAIL A 2 65 DETAIL C DETAIL D 88718976...
Page 144
Part Identification - High Speed Compact Disc ROCKSHAFT RIGHT ROCKSHAFT LEFT ROCKSHAFT CYLINDER CYLINDER 73 5 73 5 75 73 75 73 DETAIL A DETAIL B 28 3 73 16 DETAIL C 88718976...
Page 145
Part Identification - High Speed Compact Disc VALVE LEFT ROCKSHAFT RIGHT ROCKSHAFT CYLINDER CYLINDER 75 69 DETAIL A DETAIL B 88718976...
Page 146
Part Identification - High Speed Compact Disc SHUT OFF VALVE DETAIL A 65 4 DETAIL B 64 46 DETAIL C DETAIL D 88718976...
Page 147
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 21193 CLAMP HOSE 14.2 29256 COVER PLATE 32383 CLAMP-HOSE #128 TYPE F 815608 BLOCK POLYPROPELENE 3/8 PAIR 816357 PIN WELD'T TSL 1.25 X 7.375 86018376 ELBOW 90 DEGREE 86044739 HOSE CLAMP - INSULATED, 0.68"...
Page 148
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 88717828 HOSE [-06, 06-00, 06-90, 103] 88717831 TUBE, DEPTH STOP SUPPORT 88717864 ABRASIVE HOSE SLEEVE, NYLON, HSCD 88717873 TIE-HYD, FRAME FOLD, RED 88717874 TIE-HYD, JACK, YELLOW 88717875 TIE-HYD, PRV, PURPLE 88717971 HOSE [-06, 06-00, 06-00, 142] 88717972...
Page 149
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION EZBW037L WASHER LOCK 3/8 X 11/16 X 3/32 EZDR5262 PIN-CYLINDER 88718110 HOSE [-06, 06-00, 06-00, 152] - 35 88718110 HOSE [-06, 06-00, 06-00, 152] - 40 88718982 HOSE [-06, 06-00, 06-90, 285] - 35 88719015 HOSE [-06, 06-00, 06-90, 300] - 40...
Part Identification - High Speed Compact Disc BLADES 88717644...
Page 153
Part Identification - High Speed Compact Disc ITEM PART NUMBER DESCRIPTION 86512258 BOLT HEX FLG USR M12 X 25 PL 88717290 BLADE - 20" X 6.5 MM NOTCHED 88717288 BLADE - 22" X 6.5 MM NOTCHED 88719706 BLADE - 24" X 8 MM NOTCHED 88717284 BLADE - 26"...
Page 154
Part Identification - High Speed Compact Disc...
OF DISC TRANSPORT FRAME LENGTH LENGTH (MINIMUM) BLADES BEARINGS HEIGHT WIDTH HS8525 6.9 m - (22.9") 1.2 m - (4') 3.5 m - (11.6") 7.7 m - (25.5") Front 31 4.1 m - (13.5") Rear 31 HS8530 6.9 m - (22.9") 1.2 m - (4')
Specifications - High Speed Compact Disc Hydraulic Cylinders APPLICATION SIZE Hydraulic Hitch Jack Cylinder 3.5 in dia. x 12-in stroke, retracted length 24.75 in Hitch R/L Cylinders 4.0 in dia. x 8-in stroke, retracted length 20.75 in, re-phasing w/ depth stop Frame Transport Fold Cylinders 6.0 in dia.
Specifications - High Speed Compact Disc Cage Rollers Figure 162 DIMENSIONS ITEM DESCRIPTION HS8525 HS8530 HS8535 HS8540 WIDTH (LH and RH ROLLER) 2.1 m (6.11") 2.9 m (9.6") 3.6 m (11.1") 4.4 m (14.6") CENTER CAGE ROLLER 3.4 m (11.2") 3.4 m (11.2")
Specifications - High Speed Compact Disc HARDWARE TORQUE VALUES Metric Chart NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified in this manual for a specific application. Torque values listed are for general use only. Use the following charts to determine the correct torque when checking, adjusting or replacing hardware.
Specifications - High Speed Compact Disc HARDWARE TORQUE VALUES (CONT’D) Imperial Chart NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified in this manual for a specific application. Torque values listed are for general use only. Use the following charts to determine the correct torque when checking, adjusting or replacing hardware.
Specifications - High Speed Compact Disc HYDRAULIC CONNECTION SPECIFICATIONS Port Seal (O-ring Boss) Fitting O-Ring Fitting (Straight Thread) Table 7 Lubricate the O-ring before installing the fitting. Loosen Port Seal And O-ring Boss Tightening Torque the jam nut and install the fitting. Tighten the jam nut until the washer is tight against the surface.
Page 166
Specifications - High Speed Compact Disc...
Page 169
Farm King will fulfill this limited warranty by, at its option, repairing or replacing any covered part that is defective or is the result of improper workmanship, provided that the part is returned to Farm King within thirty (30) days of the date that such defect or improper workmanship is, or should have been, discovered.
Page 170
AUTHORIZED DEALER AND LABOR COSTS Repairs eligible for labor under this limited warranty must be made by Farm King or an authorized Farm King dealer. Farm King retains the exclusive discretion to determine whether it will pay labor costs for warranty repairs or replacements, and the amount of such costs that it will pay and the time in which the repairs will be made.