Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Control Unit
  5. 3110
  6. Message manual

Cisco 3110 Message Manual

Catalyst switch module for ibm bladecenter system
Hide thumbs

Advertisement

Quick Links

Download this manual
Cisco Catalyst Switch Module 3110
and 3012 for IBM BladeCenter System
Message Guide
Cisco IOS Release 12.2(40)EX2
April 2008
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-12191-01

Advertisement

loading

  Related Manuals for Cisco 3110

  Summary of Contents for Cisco 3110

  • Page 1 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide Cisco IOS Release 12.2(40)EX2 April 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
  • Page 2 OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

  • Page 3: Table Of Contents

    DOT1X_SWITCH Messages 2-21 DTP Messages 2-24 DWL Messages 2-26 EC Messages 2-26 ETHCNTR Messages 2-31 EXPRESS_SETUP Messages 2-32 FRNTEND_CTRLR Messages 2-33 GBIC_SECURITY Messages 2-34 GBIC_SECURITY_CRYPT Messages 2-36 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 4: Platform Messages

    Protocol Tunneling Messages 2-72 QOSMGR Messages 2-72 RMON Messages 2-77 SDM Messages 2-78 SPAN Messages 2-78 SPANTREE Messages 2-79 SPANTREE_FAST Messages 2-88 SPANTREE_VLAN_SW Messages 2-88 STACKMGR Messages 2-89 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 5: Switch_Qos_Tb Messages

    2-97 SWITCH_QOS_TB Messages 2-98 SW_VLAN Messages 2-98 TCAMMGR Messages 2-105 UDLD Messages 2-107 UFAST_MCAST_SW Messages 2-109 VQPCLIENT Messages 2-109 WCCP Messages 2-112 N D E X Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 6 Contents Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 7: Preface

    Cisco Catalyst Switch Module 3110 for IBM BladeCenter, Cisco Catalyst Switch Module 3012 for IBM BladeCenter, or the Catalyst Switch Module 3110 stack, referred to as the switch. Before using this guide, you should have experience working with the Cisco IOS commands and the switch software features.

  • Page 8: Conventions

    For upgrade information, see the “Downloading Software” section in the release notes. • Release Notes for the Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter • Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter Software Configuration Guide •...

  • Page 9: Obtaining Documentation And Submitting A Service Request

    Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 10 Preface Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 11: System Message Overview

    This guide also includes error messages that appear when the system fails. For information about Cisco IOS system messages that are not specific to this switch, see the Cisco IOS Software System Messages for Cisco IOS Release 12.2 on www.cisco.com.

  • Page 12: Description

    “IMAGEMGR Messages” section on page 2-43 Switch Module 3110) IP_DEVICE_TRACKING IP device tracking “IP_DEVICE_TRACKING Messages” section on page 2-44 MAC_MOVE Host activity “MAC_MOVE Messages” section on page 2-45 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 13 “SPANTREE Messages” section on page 2-79 SPANTREE_FAST Spanning-tree fast convergence “SPANTREE_FAST Messages” section on page 2-88 SPANTREE_VLAN_SW Spanning-tree VLAN switch “SPANTREE_VLAN_SW Messages” section on page 2-88 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 14: Message Severity Levels

    Normal but significant condition. 6 – informational Informational message only. 7 – debugging Message that appears during debugging only. MNEMONIC is a code that uniquely identifies the message. • Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 15: Chapter 1 System Message Overview

    [inet] Internet address All syslog messages generated by a Catalyst Switch Module 3110 other than the master switch are displayed ending with (Switch-x) where Switch-x is the number of the stack member generating the message. Syslog messages generated by the master switch are displayed with no hostname string.
  • Page 16 Bug Toolkit The Bug Toolkit provides information on open and closed caveats, and allows you to search for all known bugs in a specific Cisco IOS Release. You can access the Bug Toolkit at this URL: http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl Contacting TAC If you cannot determine the nature of the error, see the “Obtaining Documentation and Submitting a...
  • Page 17 HPSECURE Messages, page 2-41 (only the Catalyst Switch Module 3110) • • IGMP_QUERIER Messages, page 2-42 • IMAGEMGR Messages, page 2-43 (only the Catalyst Switch Module 3110) Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 18: Chapter 2 Message And Recovery Procedure

    • SW_MACAUTH Messages, page 2-97 • SWITCH_QOS_TB Messages, page 2-98 • SW_VLAN Messages, page 2-98 • • TCAMMGR Messages, page 2-105 • UDLD Messages, page 2-107 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 19: Aclmgr Messages

    Layer 2. If only the Layer 2 or Later 3 hardware table is full, only one string appears, and the other string is NULL Reduce the number of IP or MAC access lists to be applied to interfaces. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 20 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 21 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 22 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 23: Backup_Interface Messages

    A defective module is installed in the specified interface. [chars] is the interface. Explanation Remove the transceiver. If it was purchased from Cisco, contact your Cisco Recommended Action representative to have the transceiver replaced. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 24: Bspatch Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...

  • Page 25: Cfgmgr Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide OL-12191-01...
  • Page 26 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-10 OL-12191-01...

  • Page 27: Cls_Acc Messages

    Error Message CLS_ACC-2-MODE_EXITED: Complete consoleless access from mode [chars] The switch exits from consoleless access mode. [chars] is the mode. Explanation No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-11 OL-12191-01...
  • Page 28 If you still require assistance, open a case with the TAC, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...
  • Page 29 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-13 OL-12191-01...
  • Page 30 An interface has been selected for Express Setup. [chars] is the name of the interface, Explanation and [dec] is the number of the interface. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-14 OL-12191-01...

  • Page 31: Dhcp_Snooping Messages

    The DHCP snooping binding transfer process failed because of the specified reason for Explanation failure. [chars] is the reason for failure. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-15 OL-12191-01...
  • Page 32 If private VLANs are configured, the IP-source-guard filter on the primary VLAN Explanation automatically propagates to all secondary VLANs. [dec] is the secondary VLAN, and [chars] is the warning. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-16 OL-12191-01...
  • Page 33 The bindings from the database file have MAC address and VLAN information that a configured DHCP snooping binding already uses. Recommended Action No action is required. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-17 OL-12191-01...

  • Page 34: Dot1X Messages

    The system memory is not sufficient to perform IEEE 802.1x authentication. Reduce other system activity to reduce memory demands. If the switch does Recommended Action not have enough memory, upgrade to a larger memory configuration. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-18 OL-12191-01...
  • Page 35 Recommended Action Disable protocol tunnelling on the interface, and retry the IEEE 802.1x operation. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-19 OL-12191-01...
  • Page 36 The specified VLAN is out of range and cannot be assiged as an IEEE 802.1x port. [dec] is the VLAN, and [chars] is the IEEE 802.1x port. Reconfigure the configuration to use a valid VLAN. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-20 OL-12191-01...

  • Page 37: Dot1X_Switch Messages

    Change the mode of the port so that it is no longer a private VLAN host port, Recommended Action or use a valid secondary VLAN. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-21 OL-12191-01...
  • Page 38 Change either the voice VLAN or the access VLAN on the interface so that Recommended Action they are not equal. This causes Multi-Domain authentication to start. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-22 OL-12191-01...
  • Page 39 [dec] is the VLAN ID, and [chars] is the port. Recommended Action Either disable the VLAN assignment, or change the port type to a nonrouted port. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-23 OL-12191-01...

  • Page 40: Dtp Messages

    Error Message DTP-4-MEM_UNAVAIL: Memory was not available to perform the trunk negotiation action. The system cannot negotiate trunks because of a lack of memory. Explanation Reduce other system activity to ease memory demands. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-24 OL-12191-01...
  • Page 41 [chars] is the new encapsulation type. This message is provided for information only. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-25 OL-12191-01...

  • Page 42: Dwl Messages

    The listed interface joined the specified EtherChannel. The first [chars] is the physical Explanation interface, and the second [chars] is the EtherChannel interface. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-26 OL-12191-01...
  • Page 43 The system has detected that the attributes of the port now match the port-channel attributes. [chars] is the affected port. Recommended Action No action is required. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-27 OL-12191-01...
  • Page 44 In this mode, the port is placed in a suspended state. [chars] is the Layer 3 interface. Recommended Action Enable PAgP on the remote side by using the channel-group interface configuration command. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-28 OL-12191-01...
  • Page 45 Install a software image that includes LACP, and set the EC mode to on. Error Message EC-5-NOPAGP: Invalid EC mode, PAgP not enabled. PAgP is not included in the Cisco IOS image and the EtherChannel mode cannot be set Explanation to desirable or auto.
  • Page 46 EtherChannels. The first [chars] is the interface name, and the second [chars] describes the details of the unsuitable configuration. Reconfigure the port; remove the unsuitable configuration. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-30 OL-12191-01...

  • Page 47: Ethcntr Messages

    IPv4 and IPv6 frames is disabled in the switch stack. [dec] is the stack member number. Recommended Action Replace the stack member with a switch that supports forwarding of IPv4 and IPv6 frames with SNAP encapsulation. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-31 OL-12191-01...

  • Page 48: Express_Setup Messages

    Explanation No action is required. Recommended Action Error Message EXPRESS_SETUP-6-MODE_EXITED. The Express Setup mode is no longer active. Explanation No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-32 OL-12191-01...

  • Page 49: Frntend_Ctrlr Messages

    Reset the switch. If the problem is not resolved, contact your Cisco technical Recommended Action support representative because there might be a problem with the switch. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-33 OL-12191-01...

  • Page 50: Gbic_Security Messages

    GBIC_SECURITY Messages This section contains the 10-Gigabit Ethernet module security messages. The Catalyst Switch Module 3110X supports 10-Gigabit Ethernet modules and does not support Cisco Note Gigabit Interface Converter (GBIC) modules. Although the error message text refers to GBIC interfaces and modules, the messages from the switch actually refer to the 10-Gigabit Ethernet module interfaces and modules.
  • Page 51 The first [chars] is the module and the second [chars] is the interface. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-35 OL-12191-01...

  • Page 52: Gbic_Security_Crypt Messages

    The small form-factor pluggable (SFP) module was identified as a Cisco SFP module, Explanation but the switch could not match its manufacturer with one on the known list of Cisco SFP module vendors. [chars] is the port. Ensure that the Cisco IOS software running on the switch supports the SFP Recommended Action module.

  • Page 53: Gbic_Security_Unique Messages

    This message applies only to the Catalyst Switch Module 3110X. Explanation The SFP module was identified as a Cisco GBIC or SFP module, but its vendor ID and serial number match that of another interface on the system. The first [dec]/[dec] is the interface of the duplicate GBIC or SPF module, and the second [dec]/[dec] is the interface of the existing module.

  • Page 54: Hardware Messages

    If you still require assistance, open a case with the TAC, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...
  • Page 55 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-39 OL-12191-01...

  • Page 56: Hlfm Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-40 OL-12191-01...

  • Page 57: Hpsecure Messages

    [dec] is the VLAN to which the MAC address is assigned, [chars] is the interface, and the second [dec] is the stack member number. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-41 OL-12191-01...

  • Page 58: Igmp_Querier Messages

    IGMP snooping was enabled. As a result, the IGMP querier function is now enabled. Explanation [dec] is the VLAN ID. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-42 OL-12191-01...

  • Page 59: Imagemgr Messages

    [bits [hex]] is the bit representation of the switch number. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-43 OL-12191-01...

  • Page 60: Ip_Device_Tracking Messages

    The IP device tracking table could not be updated due to a lock held by another process. Explanation [dec] is the process number, and [chars] is the process. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-44 OL-12191-01...

  • Page 61: Mac_Move Messages

    Error Message PHY-4-CHECK_SUM_FAILED: SFP EEPROM data check sum failed for SFP interface [chars]. Explanation The SFP module was identified as a Cisco SFP module, but the system cannot read the vendor data information to verify whether it is correct. [chars] is the interface in which the SFP module is installed.
  • Page 62 Error Message PHY-4-MODULE_DUP: SFPs in [chars] and in [chars] have duplicate vendor-id and serial numbers. The SFP module was identified as a Cisco SFP module, but its vendor ID and serial Explanation number match that of another SFP module in the system. The first [chars] is the interface in which the SFP module is installed, the second [chars] is the interface where the duplicate SFP module is installed.

  • Page 63: Pimsn Messages

    Reduce the total number of VLANs and routed ports to be less than 1023. To Recommended Action preserve configurations and connections across reboots, save the configuration. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-47 OL-12191-01...
  • Page 64 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-48 OL-12191-01...

  • Page 65: Platform_Env Messages

    Error Message PLATFORM_FBM-4-RECOVERED: Fallback bridging recovered from resource crunch. Explanation Fallback bridging has recovered from an earlier lack of resource. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-49 OL-12191-01...

  • Page 66: Platform_Hcef Message

    Protocol (DVMRP) tunnels are supported. If the GRE tunnel is configured, remove the tunnel, or upgrade the switch software to a Cisco IOS release when the GRE feature is needed. If the ip cef accounting command is configured, remove it by using the no ip cef accounting global configuration command.

  • Page 67: Platform _Ipc Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-51 OL-12191-01...
  • Page 68 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-52 OL-12191-01...

  • Page 69: Platform_Ipv6_Ucast Message

    There is a limit of 247 labels for policy routing. [chars] is the route-map. Recommended Action Simplify the configuration with label sharing. Use the same route-maps on multiple interfaces, if possible. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-53 OL-12191-01...
  • Page 70 Modify the SDM template to enable the routing template. Use the sdm prefer Recommended Action routing configuration command, and then reload the switch by using the reload privileged EXEC command. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-54 OL-12191-01...

  • Page 71: Platform_Pm Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-55 OL-12191-01...

  • Page 72: Platform_Rpc Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-56 OL-12191-01...
  • Page 73 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-57 OL-12191-01...

  • Page 74: Platform_Ucast Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-58 OL-12191-01...
  • Page 75 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-59 OL-12191-01...
  • Page 76 Memory (TCAM) and is covered by a less specific prefix. This could be a temporary condition. The output of the show platform ip unicast failed route privileged EXEC command lists the failed prefixes. No action required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-60 OL-12191-01...

  • Page 77: Platform_Vlan Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-61 OL-12191-01...

  • Page 78: Platform_Wccp Messages

    The available memory for the switch processor is low. This can occur when too many Explanation Layer 2 VLANs are configured. [dec] is the available memory. Remove features from the system to reduce memory usage. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-62 OL-12191-01...
  • Page 79 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-63 OL-12191-01...
  • Page 80 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-64 OL-12191-01...
  • Page 81 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-65 OL-12191-01...
  • Page 82 If you still require assistance, open a case with the TA C, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...
  • Page 83 If you still require assistance, open a case with the TA C, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...
  • Page 84 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-68 OL-12191-01...
  • Page 85 For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-69 OL-12191-01...

  • Page 86: Port_Security Messages

    [chars] is the secure port. Identify the device that attempted to connect on the secure port. Notify your Recommended Action network system administrator of this condition. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-70 OL-12191-01...
  • Page 87 VLAN list change and is removed from the configuration. [int] is the VLAN ID, and [chars] is the switch port assigned to the VLAN. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-71 OL-12191-01...

  • Page 88: Qosmgr Messages

    IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-72 OL-12191-01...
  • Page 89 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-73 OL-12191-01...
  • Page 90 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-74 OL-12191-01...
  • Page 91 Recommended Action dscp-list class-map configuration command in a policy map that is attached to an egress interface. Only one match per class map is supported. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-75 OL-12191-01...
  • Page 92 Do not configure a set or trust policy-map class configuration command in a policy map and attach it to an egress interface. These policy-map actions are supported only on ingress interfaces. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-76 OL-12191-01...

  • Page 93: Rmon Messages

    Explanation the rising threshold value. [chars] is the MIB object, and [dec] is the threshold value. Recommended Action Take appropriate action on the specified object. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-77 OL-12191-01...

  • Page 94: Sdm Messages

    SPAN source sessions or one RSPAN source session. [chars] is the unavailable resource. Recommended Action Remove one of the existing SPAN or RSPAN source sessions, and retry the operation. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-78 OL-12191-01...

  • Page 95: Spantree Messages

    The BPDU guard feature can be locally configured on the interface or globally configured on all ports that have Port Fast enabled. Re-enable the interface and vlan by entering the clear errdisable privileged EXEC command. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-79 OL-12191-01...
  • Page 96 EXEC command on the remote device. After the configuration is correct, enter the shutdown and then no shutdown interface configuration commands on the associated port-channel interfaces. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-80 OL-12191-01...
  • Page 97 The first [chars] is the port name, and the second [chars] is the spanning-tree mode displayed in the show spanning-tree privileged EXEC command. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-81 OL-12191-01...
  • Page 98 When the encapsulation is consistent, spanning tree automatically unblocks the interface. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-82 OL-12191-01...
  • Page 99 When the inaccurate BPDUs have been stopped, the interfaces automatically recover and resume normal operation. Make sure that it is appropriate to have root guard enabled on the interface. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-83 OL-12191-01...
  • Page 100 The first [chars] is the interface, and the second [chars] is the spanning-tree instance. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-84 OL-12191-01...
  • Page 101 Use the spanning-tree mst pre-standard interface configuration command on Recommended Action all the interfaces to which other switches running Cisco's prestandard MST version are connected. We recommend that you migrate all the switches in the network to the IEEE MST standard version.
  • Page 102 Error Message SPANTREE-6-PORTADD_ALL_VLANS: [chars] added to all Vlans The interface has been added to all VLANs. [chars] is the added interface. Explanation No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-86 OL-12191-01...
  • Page 103 (none, ISL, or IEEE 802.1Q). When these parameters are consistent, spanning tree automatically unblocks the interface. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-87 OL-12191-01...

  • Page 104: Spantree_Fast Messages

    VLANs associated with them. You must manually enable the spanning trees that could not be created because of limited instances. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-88 OL-12191-01...

  • Page 105: Stackmgr Messages

    The stack manager received a switch-removed event for which there is no switch record. Explanation [dec] is the switch number. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-89 OL-12191-01...
  • Page 106 Subsequent SDM-6-MISMATCH_ADVISE messages explain the mismatch and recommend corrective actions. Recommended Action No action is required unless SDM_MISMATCH is displayed. For SDM_MISMATCH corrective actions, see SDM-6-MISMATCH_ADVISE. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-90 OL-12191-01...
  • Page 107 This message applies only to the Catalyst Switch Module 3110. The switch is ready. [dec] is the switch number. Explanation No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-91 OL-12191-01...

  • Page 108: Storm_Control Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-92 OL-12191-01...

  • Page 109: Supq Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-93 OL-12191-01...

  • Page 110: Sw_Dai Messages

    Error Message SUPQ-4-PORT_QUEUE_STUCK: Port queue Stuck for asic [dec] port [dec] queue [dec]. This message applies to the Catalyst Switch Module 3110 and the Catalyst Switch Module 3012. Note The system has detected that an interface queue is not being cleared in a reasonable Explanation time.
  • Page 111 [dec] is the number of packets, the second [dec] is the number of seconds, and [chars] is the affected interface. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-95 OL-12191-01...
  • Page 112 [enet]/[chars]/[enet]/[chars]/[time-of-day] is the MAC address of the sender, the IP address of the sender, the MAC address of the target, the IP address of the target, and the time of day. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-96 OL-12191-01...

  • Page 113: Sw_Macauth Messages

    [enet] is the host MAC address, [chars] [dec] is the switch ID, and the first and second [chars] are the ports between which the host traffic is flapping. Check the network switches for misconfigurations that might cause a Recommended Action data-forwarding loop. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-97 OL-12191-01...

  • Page 114: Sw_Vlan Messages

    If you still require assistance, open a case with the TA C, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...
  • Page 115 Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-99 OL-12191-01...
  • Page 116 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-100 OL-12191-01...
  • Page 117 = [chars] / file = [chars] / code = [dec] ([chars]) / bytes transferred = [dec]. The VLAN manager received an unexpected error return from a Cisco IOS file system Explanation (IFS) call while reading the VLAN database. The first [chars] is the function call name, and the second [chars] is the file name.
  • Page 118 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-102 OL-12191-01...
  • Page 119 IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-103 OL-12191-01...
  • Page 120 If you still require assistance, open a case with the TA C, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports”...

  • Page 121: Tcammgr Messages

    For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-105 OL-12191-01...
  • Page 122 For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-106 OL-12191-01...

  • Page 123: Udld Messages

    IBM technical support and provide the representative with the gathered information. For more information about the online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-107 OL-12191-01...
  • Page 124 Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools and about contacting IBM, see the “Error Message Traceback Reports” section on page 1-6. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-108 OL-12191-01...

  • Page 125: Ufast_Mcast_Sw Messages

    MAC address to an interface. [enet] is the host MAC address, and [chars] is the interface name. No action is normally required. If you think that the host should have been Recommended Action allowed access, verify the configuration on the VMPS. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-109 OL-12191-01...
  • Page 126 [chars] is the interface name. To reactivate the port, remove the excess hosts, and enter a no shutdown Recommended Action interface configuration command on the interface. Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-110 OL-12191-01...
  • Page 127 Error Message VQPCLIENT-7-RECONF: Reconfirming VMPS responses. Explanation The switch is reconfirming all responses with the VMPS. This is only a debug message. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-111 OL-12191-01...

  • Page 128: Wccp Messages

    Error Message WCCP-5-CACHEFOUND: Web Cache [IP_address] acquired. The switch has acquired the specified web cache. [IP_address] is the web cache IP Explanation address. No action is required. Recommended Action Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide 2-112 OL-12191-01...
  • Page 129 BADTRANSCEIVER messages boot loader patch messages See BSPATCH messages EC messages 2-26 BSPATCH messages ETHCNTR messages 2-31 bug toolkit EtherChannel controller messages See ETHCNTR messages Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-1 OL-12191-01...
  • Page 130 DOT1X (802.1x) 2-18 hostnames in system messages 2-24, 2-26 HPSECURE messages 2-41 2-26 2-26 ETHCNTR 2-31 EXPRESS_SETUP 2-32 IEEE 802.1x messages FRNTEND_CTRLR 2-33 See DOT1X messages Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-2 OL-12191-01...
  • Page 131 PLATFORM_IPC messages 2-51 SUPERVISOR 2-92 PLATFORM_PBR messages 2-53 SUPQ 2-93 PLATFORM_PM messages 2-55 SW_DAI 2-94 PLATFORM_RPC messages 2-56 SW_MACAUTH 2-97 PLATFORM_SPAN messages 2-58 SW_VLAN 2-98 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-3 OL-12191-01...
  • Page 132 SDM messages 2-78 TAC, contacting severity levels TCAMMGR messages 2-105 description ternary content addressable memory manager messages table See TCAMMGR messages Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-4 OL-12191-01...
  • Page 133 VLAN manager messages See SW_VLAN messages VLAN Query Protocol client messages See VQPCLIENT messages VQPCLIENT messages 2-109 VTP messages See SW_VLAN messages WCCP messages 2-62 Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-5 OL-12191-01...
  • Page 134 Index Cisco Catalyst Switch Module 3110 and 3012 for IBM BladeCenter System Message Guide IN-6 OL-12191-01...

This manual is also suitable for:

3112