Analog Audio Input Level Settings By Steps; Analog Audio Output Level Settings - Lightware HDMI-3D-OPT-TX210A User Manual


  
7. LW3 Programmer's Reference
7.7.18. Analog Audio Input Level Settings by Steps
INFO: The following settings are valid only for analog audio input ports of the transmitters.
Volume in dB
Command format: CALL●/MEDIA/AUDIO/<I
Response format: m0●/MEDIA/AUDIO/<I
Parameters:
<step> Volume is increased or decreased with the given value in dB.
Example:
˃ CALL /MEDIA/AUDIO/I5:stepVolumedB(-1)
˂ m0 /MEDIA/AUDIO/I5:stepVolumedB
Explanation: The volume is decreased with 1 dB, the current volume is -1 dB which means 91.21% in percent.
Volume in Percent
Command format: CALL●/MEDIA/AUDIO/<I
Response format: m0●/MEDIA/AUDIO/<I
Parameters:
<step> Volume is increased or decreased with the given value in percent.
Example:
˃ CALL /MEDIA/AUDIO/I5:stepVolumePercent(5)
˂ m0 /MEDIA/AUDIO/I5:stepVolumePercent
Explanation: The volume is increased with 5%, the current volume is -0.83 dB which means 95% in percent.
Balance
Command format: CALL●/MEDIA/AUDIO/<I
Response format: m0●/MEDIA/AUDIO/<I
Parameters:
<step> Balance is shifted to left or right depends on the given value. -100 means
left balance, 100 means right balance, step is 1. Center is 0 (default).
Example:
˃ CALL /MEDIA/AUDIO/I5:stepBalance(1)
˂ m0 /MEDIA/AUDIO/I5:stepBalance
Explanation: The balance is shifted to right with 1 step.
>.stepVolumedB=<step>
n
>.stepVolumedB=<step>
n
>.stepVolumePercent=<step>
n
>.stepVolumePercent=<step>
n
>.stepBalance=<step>
n
>.stepBalance=<step>
n
HDMI-3D-OPT series – User's Manual
7.7.19. Analog Audio Output Level Settings
INFO: The following settings are valid only for analog audio output port of the receiver.
Volume (dB)
Command format: SET●/MEDIA/AUDIO/<O
Response format: pw●/MEDIA/AUDIO/<O
Parameters:
<level>
Example:
˃ SET /MEDIA/AUDIO/O3.VolumedB=-15
˂ pw /MEDIA/AUDIO/O3.VolumedB=-15.00
Volume (Percent)
Command format: SET●/MEDIA/AUDIO/<O
Response format: pw●/MEDIA/AUDIO/<O
Parameters:
<level>
Example:
˃ SET /MEDIA/AUDIO/O3.VolumePercent=50
˂ pw /MEDIA/AUDIO/O3.VolumePercent=50.00
Balance
Command format: SET●/MEDIA/AUDIO/<O
Response format: pw●/MEDIA/AUDIO/<O
Parameters:
<level>
Example:
˃ SET /MEDIA/AUDIO/O3.Balance=0
˂ pw /MEDIA/AUDIO/O3.Balance=0
>.VolumedB=<level>
n
>.VolumedB=<level>
n
Sets the output volume (attenuation) between -95.625 dB and 0 dB in step
of -0.375 dB. The value is rounded up if necessary to match with the step
value.
>.VolumePercent=<percent>
n
>.VolumePercent=<percent>
n
Sets the output volume (attenuation) between 100% and 0%, in step of 1%.
The value is rounded up if necessary to match with the step value.
>.Balance=<level>
n
>.Balance=<level>
n
Sets the balance; -100 means left balance, 100 means right balance, step
is 1. Center is 0 (default).
67