Analog Audio Output Level Settings By Steps; Network Configuration; Query The Dhcp State; Change The Dhcp State - Lightware HDMI-3D-OPT-TX210A User Manual


  
7. LW3 Programmer's Reference
7.7.20. Analog Audio Output Level Settings by Steps
INFO: The following settings are valid only for analog audio output port of the receiver.
Volume in dB
Command format: CALL●/MEDIA/AUDIO/<O
Response format: m0●/MEDIA/AUDIO/<O
Parameters:
<step> Volume is increased or decreased with the given value in dB.
Example:
˃ CALL /MEDIA/AUDIO/O3:stepVolumedB(-1)
˂ m0 /MEDIA/AUDIO/O3:stepVolumedB
Explanation:
The volume is decreased with 1 dB, the current volume is -1.95 dB which means 77.84% in percent.
Volume in Percent
Command format: CALL●/MEDIA/AUDIO/<O
Response format: m0●/MEDIA/AUDIO/<O
Parameters:
<step> Volume is increased or decreased with the given value in percent.
Example:
˃ CALL /MEDIA/AUDIO/O3:stepVolumePercent(5)
˂ m0 /MEDIA/AUDIO/O3:stepVolumePercent
Explanation:
The volume is increased with 5%, the current volume is -1.52 dB which means 82.84% in percent.
7.8. Network Configuration
7.8.1. Query the DHCP State
Command format: GET●/MANAGEMENT/NETWORK.DhcpEnabled
Response format: pw●/MANAGEMENT/NETWORK.DhcpEnabled=true|false
Example:
˃ GET /MANAGEMENT/NETWORK.DhcpEnabled
˂ pw /MANAGEMENT/NETWORK.DhcpEnabled=true
>.stepVolumedB=<step>
n
>.stepVolumedB=<step>
n
>.stepVolumePercent=<step>
n
>.stepVolumePercent=<step>
n
HDMI-3D-OPT series – User's Manual
7.8.2. Change the DHCP State
Command format: SET●/MANAGEMENT/NETWORK.DhcpEnabled=true|false
Response format: pw●/MANAGEMENT/NETWORK.DhcpEnabled=true|false
Example:
˃ SET /MANAGEMENT/NETWORK.DhcpEnabled=false
˂ pw /MANAGEMENT/NETWORK.DhcpEnabled=false
7.8.3. Query the IP Address
Command format: GET●/MANAGEMENT/NETWORK.IpAddress
Response format: pr●/MANAGEMENT/NETWORK.IpAddress=<IP_Address>
Example:
˃ GET /MANAGEMENT/NETWORK.IpAddress
˂ pr /MANAGEMENT/NETWORK.IpAddress=192.168.0.100
7.8.4. Change the IP Address (Static)
Command format: SET●/MANAGEMENT/NETWORK.StaticIpAddress=<IP_address>
Response format: pw●/MANAGEMENT/NETWORK.StaticIpAddress=<IP_address>
Example:
˃ SET /MANAGEMENT/NETWORK.StaticIpAddress=192.168.0.85
˂ pw /MANAGEMENT/NETWORK.StaticIpAddress=192.168.0.85
7.8.5. Query the Subnet Mask
Command format: GET●/MANAGEMENT/NETWORK.NetworkMask
Response format: pr●/MANAGEMENT/NETWORK.NetworkMask=<netmask>
Example:
˃ GET /MANAGEMENT/NETWORK.NetworkMask
˂ pr /MANAGEMENT/NETWORK.NetworkMask=255.255.255.0
7.8.6. Change the Subnet Mask (Static)
Command format: SET●/MANAGEMENT/NETWORK.StaticNetworkMask=<netmask>
Response format: pw●/MANAGEMENT/NETWORK.StaticNetworkMask=<netmask>
Example:
˃ SET /MANAGEMENT/NETWORK.StaticNetworkMask=255.255.255.0
˂ pw /MANAGEMENT/NETWORK.StaticNetworkMask=255.255.255.0
68