Xconfiguration Video Input Connector [1..5] Quality; Xconfiguration Video Monitors - Cisco MX700 Reference Manual

Cisco TelePresence MX700 and MX800

Introduction

xConfiguration Video Input Connector [1..5] Quality

When encoding and transmitting video there is a trade-off between high resolution and high
frame rate. For some video sources it is more important to transmit high frame rate than high
resolution and vice versa. This setting specifies whether to give priority to high frame rate or to
high resolution.
Requires user role: ADMIN, INTEGRATOR
Default value: Connector 1, 2, 5: Motion Connector 3, 4: Sharpness
USAGE:
xConfiguration Video Input Connector
where
n
: Unique ID that identifies the video input connector. Range: 1..5
Quality
: Motion/Sharpness
Motion: Gives the highest possible frame rate. Used when there is a need for higher
frame rates, typically when a large number of participants are present or when there is
a lot of motion in the picture.
Sharpness: Gives the highest possible resolution. Used when you want the highest
quality of detailed images and graphics.
xConfiguration Video Input Connector [1..5] Visibility
Define the visibility of the video input connector in the menus on the user interface.
Requires user role: ADMIN, INTEGRATOR
Default value: Connector 1, 2, 3: IfSignal Connector 4: Always Connector 5: Never
USAGE:
xConfiguration Video Input Connector
where
n
: Unique ID that identifies the video input connector. Range: 1..5
Visibility
: Always/IfSignal/Never
Always: The menu selection for the video input connector will always be visible on the
user interface.
IfSignal: Yhe menu selection for the video input connector will only be visible when
something is connected to the video input.
Never: The input source is not expected to be used as a presentation source, and will
not show up on the user interface.
D15335.08 Cisco TelePresence MX700 and MX800 API Reference Guide CE9.2, NOVEMBER 2017.
About the API xConfiguration xConfiguration
n Quality: Quality
Visibility:
n Visibility
xCommand

xConfiguration Video Monitors

A role is assigned to each monitor using the Video Output Connector [n] MonitorRole setting.
The monitor role decides which layout (call participants and presentation) will appear on the
monitor that is connected to this output. Monitors with the same monitor role will get the same
layout; monitors with different monitor roles will have different layouts.
The monitor layout mode that is set in the Video Monitors setting should reflect the number of
different layouts you want in your room setup. Note that some monitors can be reserved for
presentations.
Requires user role: ADMIN, INTEGRATOR
Default value: Auto
USAGE:
xConfiguration Video Monitors:
where
Monitors
: Auto/Single/Dual/DualPresentationOnly/TriplePresentationOnly/Triple
Auto: The number of monitors connected to the codec is automatically detected, and
the layout is distributed on the monitors according to the MonitorRole settings.
Single: The same layout is shown on all monitors.
Dual: The layout is distributed on monitors with monitor role First and Second. If a
presentation is part of the layout, all participants in the call are shown on monitors with
monitor role First, and the presentation is shown on monitors with monitor role Second.
DualPresentationOnly: All participants in the call are shown on monitors with monitor
role First. If a presentation is part of the layout, the presentation is shown on monitors
with monitor role Second.
Triple: The layout is distributed on monitors with monitor role First, Second and Third.
Monitors with monitor role Second are used first, then First, and finally Third. If a
presentation is part of the layout, all participants in the call are shown on monitors
with monitor role First and Second, and the presentation is shown on the monitor with
monitor role Third.
TriplePresentationOnly: All participants in the call are distributed on monitors with
monitor role First and Second. Monitors with monitor role Second are used first, then
First. If a presentation is part of the layout, the presentation is shown on the monitor
with monitor role Third.
103
API Reference Guide
xStatus Appendices
Monitors
Copyright © 2017 Cisco Systems, Inc. All rights reserved.