If the changes in the audio See the Audio Level table in the Physical Interface Guide for Cisco TelePresence SX80 for a conditions are significant, the echo canceller may take a second or two to re-adjust.
Define the level of the Microphone input connector. connector can be set to line or microphone mode. See the Audio Level table in the Physical Interface Guide for Cisco TelePresence SX80 for a Requires user role: ADMIN, INTEGRATOR complete overview of the values represented in dB.
This setting applies to the Intelligent Proximity feature. Set the maximum volume of the ultra- sound pairing message. See the Audio Level table in the Physical Interface Guide for Cisco TelePresence SX80 for a complete overview of the values represented in dB.
Typical situations where the codec does not receive EDID information are: when you connect DefaultMode : Off/On a Cisco TelePresence Precision 60 camera using 3G-SDI; when you connect a Cisco Off: Turn off the camera backlight compensation. TelePresence Precision 40 (Cisco TelePresence PrecisionHD 1080p4xS2) camera; when you use an HDMI repeater that does not pass on EDID information.
If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the Requires user role: ADMIN system cannot register, the auto-selection chooses H323. Default value: Off H320: All calls are set up as H.320 calls (only applicable if connected to Cisco TelePresence ISDN Link). USAGE: xConfiguration Conference AutoAnswer Mute: Mute H323: All calls are set up as H.323 calls.
Network  IPv4 Assignment Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients without the need for client certificates. Developed by Microsoft, Cisco and RSA Security. Define how the system will obtain its IPv4 address, subnet mask and gateway address. This setting applies only to systems on IPv4 networks.
NetworkServices CDP Mode: Mode Mode : Auto/Manual/Off where Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. Mode : Off/On If CDP is not available, VLAN is not enabled. Off: The CDP daemon is disabled.
The HTTP Proxy Settings are available from the user interface when the system is provisioned xConfiguration NetworkServices HTTP Proxy Password: "Password" to Cisco Spark. The HTTP proxy settings makes it possible to onboard a video system behind a HTTP proxy to Spark.
NetworkServices HTTP Proxy Mode xConfiguration NetworkServices HTTPS Server MinimumTLSVersion The HTTP proxy for Cisco Spark can be set up manually or turned off. Set the lowest version of the TLS (Transport Layer Security) protocol that is allowed. Requires user role: ADMIN, USER...
SNMP Agent in the codec. The default password is Requires user role: ADMIN "public". If you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP Community is configured there too. NOTE: The SNMP Community password is Default value: ReadOnly case sensitive.
Requires user role: ADMIN xConfiguration Peripherals Profile TouchPanels Default value: Off Define the number of Cisco Touch controllers that are expected to be connected to the video USAGE: system. This information is used by the video system's diagnostics service. If the number of...
When the video system emits ultrasound, Proximity clients can detect that they are close to the Default value: "" video system. In order to use a client, at least one of the Proximity services must be enabled (refer to the Proximity Services settings). In general, Cisco recommends enabling all the USAGE: Proximity services.
Number, Protocol, CallRate, CallType and Device. You can add several contact methods to a contact. Note that only the first contact method will appear in the Favorites list on the Cisco TelePresence Touch controller. The first contact Requires user role: ADMIN, USER method may have been created when issuing the xCommand Phonebook Contact Add command to make the contact.
UserInterface Message TextInput Display Enter the text to appear on the feedback options. Displays an input dialog box to which a user can respond, on the Cisco Telepresence Touch 10 Option.4: String (0, 255) and on the main screen of the Cisco DX80.
SIP Verified Shows whether or not the SSL certificate of the server that the video system / codec tries to register to is included in the codec’s trusted CA-list. The server is typically a Cisco VCS or xStatus Standby PowerSave State CUCM.
SystemUnit Hardware Module CompatibilityLevel Requires user role: ADMIN, USER The Cisco TelePresence endpoints are using a NAND flash memory for general storage. The Value space of the result returned: endpoints running TC software are manufactured with a new version of the flash memory.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third- party trademarks mentioned are the property of their respective owners.