Download  Print this page

Advertisement

Installation guide
for Cisco TelePresence MX700 Single Camera
on a free standing floor stand or a floor stand secured to the wall
78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved.
http://www.cisco.com/go/mx-docs

Advertisement

Table of Contents

   Summary of Contents for Cisco TelePresence MX700

  • Page 1 Installation guide for Cisco TelePresence MX700 Single Camera on a free standing floor stand or a floor stand secured to the wall 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. http://www.cisco.com/go/mx-docs...
  • Page 2 The user documentation for this product, including compliance and safety information, can be found on the Cisco web site, http://www.cisco.com/go/mx-docs Floor stand secured to the wall 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 2...
  • Page 3 WARNING: This is a class A product. In a domestic environment this product may cause radio interference in which case the user 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 3 may be required to take adequate measures.
  • Page 4 Remove covers from floor stand parts Set aside the covers. They will be replaced when the system is fully assembled and tested (step 20). Front 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 4...
  • Page 5 8 × M6x12 first on one side; then on the other. (countersunk) Six screws from the back and two from the top. 8 × M6x12 (countersunk) 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 5...
  • Page 6 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Fasten center bracket 2 × M6x12 (pan) Front 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 6...
  • Page 7 Mount the feet to the floor stand to allow it to be free standing Option B (secured to the wall) is described on the next page. 4 × M6x35 (countersunk) Front 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 7...
  • Page 8 Front illustration). Fasten the floor stand to the wall brackets with the 4 × M6x12 (pan) four screws (provided). Side view 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 8...
  • Page 9 The screws with wing nut, which you can see from the sides of the monitor, must enter the center slot on each side of the floor stand. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 9...
  • Page 10 Tighten the wing nuts on both sides. They are accessed from the sides of the monitor. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 10...
  • Page 11 9. 4 × M6x35 (countersunk) Enter four screws from front and four screws from underneath. Then, tighten all screws. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 11...
  • Page 12 Do not let go of the monitor before it is securely placed on the floor stand. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 12...
  • Page 13 Make sure the power switch next to the socket is in its ON position. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 13...
  • Page 14 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Remove support handles Unscrew the screws (4 × M4x8) and remove the support handles. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 14...
  • Page 15 Place the joining bracket in the channel. Make sure it aligns with the channel at top. Push down the lever to 7 × M6x12 (pan) horizontal position. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 15...
  • Page 16 Lead the guidance pins on the back cover into the holes. Lower the back cover toward the system. The cover snaps to magnets. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 16...
  • Page 17 The cables will be connected in steps 14, 16 and 17. Loudspeaker Camera Monitor Loudspeaker PoE injector cables 3-5 cables cables cables 1-5 cable × 3 × 5 Left Right monitor monitor 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 17...
  • Page 18 Connect cables to right monitor and PoE injector SWITCH Ethernet Power over Ethernet injector COLOR HDMI DO NOT CALIBRATION REMOVE HDMI USB (type B) Right monitor connector panel 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 18...
  • Page 19 Fasten the stud to the top profile with one screw from above. Repeat this step for the left side. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 19...
  • Page 20 Enter the camera cover in the clips 2 × M4x8 (pan) at the bottom, and align it with the back panels. The cover snaps to magnets. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 20...
  • Page 21 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Connect camera cables DAISY VISCA CHAIN HDMI Power Ethernet Camera connector panel 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 21...
  • Page 22 8 × PT4x10 Enter the loudspeaker onto the speaker clip. Fasten with one screw. (one for each loudspeaker) Make sure the cable is not pinched. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 22...
  • Page 23 CAT 5e, shielded Ethernet cable, 5 m. extension cord and country specific cable Codec connector panel Two presentation cables are provided: HDMI ↔ HDMI; and DVI/Euroblock ↔ VGA/mini jack. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 23...
  • Page 24 The Ethernet socket is behind the lid at the rear of Touch 10. The cable is rated for PoE use, 12.5 m, flat. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 24...
  • Page 25 This is described in the Getting Started Guide, which can be found on the Cisco web site. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 25...
  • Page 26 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Mount covers The top cover is fastened by clips. The other covers snap to magnets. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 26...
  • Page 27 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Mount textile grilles L, M Use the provided gloves when handling the textile grilles. The grilles snap to magnets. 78-100218-01 A0 | 2014 APRIL | © 2014 Cisco Systems, Inc. All rights reserved. Page 27...
  • Page 28 Installation guide for Cisco TelePresence MX700 Single camera - Floor stand Cisco has more than 200 offices worldwide. Find an overview of the offices on the Cisco web site at http://www.cisco.com/go/offices Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S.and other countries.

Comments to this Manuals

Symbols: 0
Latest comments: