Piper Navajo Chieftain PA-31-350 Service Manual page 8

NAVAJO CHIEFTAIN SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont)
Aerofiche
Figure
Grid No.
5-31.
Fabricated Bellcrank Rigging Tool ................
...........................
IL4
5-32.
Fabricated Aileron and Elevator Rigging Tool .................................
L5
5-33.
Fabricated Rudder Rigging Tool ............................................
IL6
6-1.
Schematic of Power Pack Electrical System ...................................
2A 13
6-2.
Schematic Diagram of Hydraulic System .....................................
2A 14
6-3.
Power Pack Installation ..............
....................
..................
2A23
6-4.
Identification of Power Pack ................................................
2A24
6-5.
Location of Power Pack Components (Ozone) ................................
2B1
6-6.
Hydraulic Power Pack (Ozone) .................................
.............
2B
6-7.
Power Pack Manifold (Ozone) ..............................................
2B7
6-8.
Power Pack Handle-Release Mechanism (Ozone) ..............................
2B12
6-9.
Safetying Control Arm (Ozone) .............................................
2B13
6-10.
Timing of Selector Spool (Ozone) ............................................
B 14
6-11.
Handle-Release Adjustment (Ozone) .........................................
2B14
6-12.
Location of Power Pack Components (Wiebel Tool) ...........................
2B18
6-13.
Hydraulic Power Pack (Wiebel Tool) ........................................
2B20
6-14.
Power Pack Manifold (Wiebel Tool) .........................................
B23
6-15.
Power Pack Handle-Release Mechanism (Wiebel Tool) .........................
2C
6-16.
Safetying Control Arm (Wiebel Tool) ........................................
C4
6-17.
Indexing of Selector Spool (Wiebel Tool) .....................................
2C5
6-18.
Handle-Release Adjustment (Wiebel Tool) ....................................
'C7
6-19.
Landing Gear Selector Mechanism ................
...........................
2C10
6-20.
Hand Pump (Ozone) .....................
...................................
2C
6-21.
Hand Pump (Wiebel Tool).............................................
.....
2C 16
6-22.
Hydraulic System Installation ...............................................
2C 1
6-23.
Gear Actuating Cylinder (Ozone) ............................................
C 19
6-24.
Gear Actuating Cylinder (Wiebel Tool) .......................................
2C21
6-25.
Gear Door Actuating Cylinder (Ozone) .......................................
2C23
6-26.
Gear Door Actuating Cylinder (Wiebel Tool) ................
..................
2D1
6-27.
Hydraulic Filter ...........................................................
2D3
6-28. Hydraulic Pump.2D6
6-28.
Hydraulic Pump ...........................................................
2
6-29.
Power Pack Test Harness Schematic .........................................
2
D10
7-1.
Nose Gear Oleo Strut Assembly ..............................................
2D18
7-2.
Nose Gear Steering Assembly (S N 31-7852141 and up)
......................
2D20
7-3.
Nose Landing Gear Installation .................
.................
.
..... 2 D24
7-4.
Clamping Rudder Pedals in Neutral Position ..................................
2E5
7-5.
Rudder Pedals Neutral Angle ...............................................
E5
7-6.
Aligning Nose Gear ........................................................
2E5
7-7.
Correct Method of Installing Rod End Bearings ...............................
2E8
7-8.
Main Gear Oleo Strut Assembly .....................................
.. . 2E9
7-9.
Main Landing Gear Installation (Left) ........................................
2E15
7-10.
Actuator Cylinder .........................................................
2E17
7-11.
Aligning Main Gear ......................................
.................
2E19
7-12.
Landing Gear Circuit Diagram ...............................
. .........
2E21
Revised: 3/5/84
1A8