Piper Navajo Chieftain PA-31-350 Service Manual page 276

NAVAJO CHIEFTAIN SERVICE MANUAL
LIST OF ILLUSTRATIONS (cont)
Aerofiche
Grid No.
Figure
7-17.
7-18.
7-19.
7-20.
7-21.
7-22.
7-23.
7-24.
7-25.
7-26.
7-27.
7-28.
7-29.
7-30.
Brake Installation (Typical) .................................................
Brake Disc Minimum Thickness .............................................
Wheel Brake Assembly (Cleveland 30-68 A and B) .............................
Wheel Brake Assembly (Cleveland 30-95 and 30-95a) ...........................
Wheel Brake Assembly Cleveland 30 - 123 ....................................
Removal and Installation of Anchor Bolts ....................................
Brake Master Cylinder Assembly ............................................
Parking Brake Valve Assembly ..............................................
Bleeding Brake (Typical)....................................................
Main Wheel Assembly .....................................................
Wheel Brake Assembly .....................................................
Snow Shield Modification ....
Rivet Head Grinding Limits...
Wear Pad - Wear Limits......
........
........
I
7-31. Limits for Repadded Pressure and Back Plates ..................
7-32. Brake Disc Visual Check for Serviceable Limits .................
7-33. Fabricated Rivet Tool (Goodyear only).........................
7-34. Fabricated Tool, Checking Nose Wheel Alignment ...............
7-35. Fabricated Tool, Checking Nose Gear Link Travel ...............
7-36. Fabricated Tool, Checking Main Gear Side Brace Link Travel ..
7-37. Fabricated Tool, Checking Main Gear Toe-in Adjustment ........
7-38. Nose Gear Wear Limits ......................................
7-39. Main Gear Wear Limits ......................................
8-1. Engine Cowling .............................................
8-2. Cowl Flap Transmission and Sender Assembly ..................
8-3. Propeller Installation.........................................
8-4. Typical Nicks and Removal Method ...........................
8-5. Propeller Governor .........................................
8-6. Engine Installation...........................................
8-7. Schematic Diagram of Turbocharger System ....................
8-8. Turbocharger Installation, PA-31-350 ..........................
8-9. Exhaust Waste Gate ........................................
8-10. Fuel Injector ................................................
8-11. Fuel-Air Bleed Nozzle ........................................
..............
..............
..............
..............
..............
..............
............
..............
............
..............
...........
..............
...... .....
.............
...............
..............
..............
..............
..............
..............
...............
..............
2F5
2F7
2F8
2F8
2F9
2FIO
2FII
2F13
2F13
2F20
2F21
2F23
2F24
2G5
2G5
2G6
2G15
2G16
2G17
2G18
2G19
2G20
2G23
2H8
2H8
2H12
2H14
2H16
2H21
215
216
217
219
2113
2113
2113
2114
2114
2116
2116
2117
2118
2119
2119
2119
8-12.
8-13.
8-14.
8-15.
8-16.
8-17.
8-18.
8-19.
8-20.
8-21.
8-22.
Height of Spring in Distributor Block Tower..................................
Contact Points ............................................................
Engine Timing Marks ......................................................
Timing Light Connected to Magneto .........................................
Timing Marks on Rotating Magneto (Present) ................................
Timing Marks on Magneto Rotor (Earlier). ...................................
Painted Tooth Centered in Timing Window ...................................
Cam End View of Magneto .................................................
Timing Mark on Rotor Aligned with Pointer (Right-Hand Rotation).............
Timing Light Connected to Magneto .........................................
Timing Light Connected to Magneto and Breakers.............................
Revised: 10/15/82
2A5