Xerox DocuColor 2240 Service Manual page 983

Table 2 Output Component Control Codes
Code Name Description
004-011 Drum Motor YMC Rotate at low speed. Remove all Drum Car-
(52mm/sec.) tridges before energizing to prevent Belt
damage.
004-012 IBT Motor (52mm/ Rotate at low speed. Operate with the IBT
sec.) Assy. removed to prevent Transfer Belt
damage.
004-013 IBT Motor (high Rotate at high speed. Operate with the IBT
speed) unit removed. The Belt might be damaged
since the Belt Work Control is not per-
formed.
004-014 IBT_5V ON ON = High.
004-050 Fuser Fan, LV Fan Rotate the FUSER FAN, LV FAN and
and Rear Fan REAR FAN at high speed. (Rotation is Low
Rotation High at Power ON)
speed
005-011 Set Gate Solenoid Turn Set Gate Open ON (Towards bottom
Open of Nudger Roll) for 5sec -> Auto OFF
005-012 Set Gate Solenoid Turn Set Gate Close ON (Towards bottom
Close of Nudger Roll) for 5sec -> Auto OFF
005-040 Feed Mot. DADF Feed Motor for 2sec -> Auto OFF
005-055 Belt Motor Non Rotate the DADF Belt Motor forward.
CVT Mode (CW)
005-056 Belt Motor Non Rotate the DADF Belt Motor backward.
CVT Mode (CCW)
005-075 Regi Gate Solenoid Push the Regi Gate with the Arm to turn it
ON for 5sec -> Auto OFF
005-081 Exit Motor Non Operate the DADF Exit Motor
CVT Mode
005-083 Doc Ready switch ON the Doc Ready signal.
005-084 Doc Set LED switch ON the DOC SET LED
006-002 IIT Exposure Lamp switch the Lamp ON for 180sec -> Auto
OFF
006-004 IPS Cooling Fan After operating the IPS Cooling Fan at high
(Low speed) speed for 5sec, operate it at low speed. ON
= FAN. ON = 24V, FAN Slow: L->H (About
13V)
006-005 IIT Scan Motor More it 50mm from current position in Scan
(Scan) direction -> Auto OFF
006-006 IIT Scan Motor More it 50mm from current position in
(Return) Return direction -> Auto OFF
006-014 IPS Cooling Fan Operate the IPS Cooling Fan at high
(High speed) speed.
006-030 LD ON Enable Sig-
nal (concurrently
for 4 colors)
Initial issue
DC 3535/2240/1632
Conflicts Code Name
004-003 006-031 Polygon Motor
Start Signal
006-032 SOS Gain
004-002,
006-086 IIT Image Area
004-013
006-091 Exchange To ADF
004-002,
004-012
007-003 Tray 5 FEED
Clutch
007-004 HOTLINE_TRAY
-
008-001 #1Feed Motor
-
(Fwd)
008-002 #1Feed Motor
(Rev)
-
-
008-003 #2Feed Motor
(Fwd)
-
008-004 #2Feed Motor
005-056
(Rev)
005-055
- 008-005 #3Feed Motor
(Fwd)
- 008-006 #3Feed Motor
(Rev)
-
-
-
008-007 #4Feed Motor
(Fwd)
-
008-008 #4Feed Motor
(Rev)
006-006
008-009 Dup Motor
006-005
(200.1mm/sec.)
-
008-010 Dup Motor
(104mm/sec.)
-
02/03
6-91
Table 2 Output Component Control Codes
Description
Start-of-Scan Sensor gain signal
IMG-AREA Signal Output. ON = P727
LVDS (Differential) High
Turn ON the document exchange com-
mand signal to the DADF
Not used.
Feed (Rotate #1Feed Motor in paper feed
direction at 200mm/sec.)
It switches OFF automatically 6sec after
LiftUp has started, or when the Level Snr
detected LiftUp. LiftUp cannot be per-
formed when the Level Snr should detect
LiftUp.
Feed (Turn #2Feed Motor On in paper feed
direction at 192mm/sec.)
It switches OFF automatically 6sec after
LiftUp has started, or when the Level Snr
detected LiftUp. LiftUp cannot be per-
formed when the Level Snr should detect
LiftUp.
Feed (Turn #3Feed Motor On in paper feed
direction at 192mm/sec.)
It switches OFF automatically 6sec after
LiftUp has started, or when the Level Snr
detected LiftUp. LiftUp cannot be per-
formed when the Level Snr should detect
LiftUp.
Feed (Turn #4Feed Motor On in paper feed
direction at 192mm/sec.)
It switches OFF automatically 6sec after
LiftUp has started, or when the Level Snr
detected LiftUp. LiftUp cannot be per-
formed when the Level Snr should detect
LiftUp.
Start operation. Switches OFF automati-
cally at 1000msec.
Start operation. Switches OFF automati-
cally at 1000msec.
General Procedures and Information
Conflicts
-
-
-
-
-
8-002
8-001
8-004
8-003
8-005
8-008
8-007
8-010, 011,
012, 053, 054,
055, 056
8-009, 011,
012, 053, 054,
055, 056
dC330