Xerox DocuColor 2240 Service Manual page 985

Table 2 Output Component Control Codes
Code Name Description
009-002 #M_Disp MOT M Color Disp. MOT turns ON, and switches
OFF automatically after 5sec.
009-003 #C_Disp MOT C Color Disp. MOT turns ON, and switches
OFF automatically after 5sec.
009-004 #K_Disp MOT K Color Disp. MOT turns ON, and switches
OFF automatically after 5sec.
009-005 #Y_DB DC Y Color Developer Bias DC Component
Output
009-006 #M_DB DC M Color Developer Bias DC Component
Output
009-007 #C_DB DC C Color Developer Bias DC Component
Output
009-008 #K_DB DC K Color Developer Bias DC Component
Output
009-009 #YM_DB AC YM Color Developer Bias AC Component
Output
009-012 #CK_DB AC CK Color Developer Bias AC Component
Output
009-013 Dev_CL The clutch for driving K Color turns ON,
and switches OFF automatically after 5
sec.
009-014 Dev_MOT Normal- Switches off automatically after 5 sec.
speed
009-016 Dev_MOT Half- Switches off automatically after 5sec.
speed
009-017 Dev_MOT High- Switches off automatically after 5sec.
speed
009-018 Dev bias AC Switch on before starting BCR DC for each
enable color.
009-026 #Y_BCR DC High voltage output value of BCR DC_Y.
ON = PWM
009-027 #M_BCR DC High voltage output value of BCR DC_M.
ON = PWM
009-028 #C_BCR DC High voltage output value of BCR DC_C.
ON = PWM
009-029 #K_BCR DC High voltage output value of BCR DC_K.
ON = PWM
009-030 #Y_BCR AC High voltage output value of BCR AC_Y.
ON = PWM
009-031 #M_BCR AC High voltage output value of BCR AC_M
009-032 #C_BCR AC High voltage output value of BCR AC_C
009-033 #K_BCR AC High voltage output value of BCR AC_K
009-034 AGT MOT Agitator MOT ON
009-035 CRUM PWR Power ON for CRUM-YMCK
Initial issue
DC 3535/2240/1632
Conflicts Code Name
- 009-037 Dev DC chg (K)
009-038 BCR ACDC K CHG DEVE_AC_K changes at connector termi-
-
009-039 BCRAC Clock
-
009-040 ROS Shutter Close ROS Shutter: Rotates in Close direction
-
009-041 ROS Shutter Open ROS Shutter: Rotates in Open direction
-
009-042 #K_Erase Lamp
-
009-045 #YMC_Erase Lamp YMC ERASE LAMP lit.
009-051 2nd BTR Contact
-
-
009-052 2nd BTR Retract
-
009-053 De Tack Saw HV
009-054 1st BTR Contact
-
009-055 1st BTR Retract
009-016,-017
009-056 2nd BTR Select
009-076 Specular reflection
009-014, -017
LED
009-016, -017
009-077 Diffusion reflection
LED
009-078 ADC Sensor Shut-
ter Open
009-030
009-079 ADC Sensor Shut-
ter Close
009-031
009-080 ATC Sensor 5V ON 5V Power supply to ATC SNR.
010-001 OCT Motor (CW)
009-032
010-002 OCT Motor (CCW) Switches on reverse and switches off auto-
9-33
012-001 Main Drive Motor
009-026
On/Off
012-010 Rear Tamper Motor
009-027
Low Front On/Off
009-028
009-029
02/03
6-93
Table 2 Output Component Control Codes
Description
nals trailing.
Frequency signal common to BCR AC All
Colors.
(Brush: Contact direction).
(Brush: Retract direction). ON = H
K ERASE LAMP lit.
BTR2 Retract MOT. Switches off 800ms
after the Retract SNR detected the Contact
Position (High).
Switches off 60ms after the Retract SNR
detected the Retract Position (Low).
Turn on DTS HV.
Switches off 100ms after the Retract SNR
detected the Contact Position (High).
Switches off 100ms after the Retract SNR
detected the Retract Position (Low).
selects polarity of bias voltage
When the Specular Reflection LED of ADC
SNR turns ON and YMC density is
detected.
When the Diffusion Reflection LED of ADC
SNR turns ON and K density is detected.
Switches off automatically after 100msec.
Switches off automatically after 100msec.
Switches on forward and switches off auto-
matically at 150msec.
matically at 150msec.
Switches off automatically after 100pulses.
General Procedures and Information
Conflicts
009-041
009-040
-
-
-
-
-
-
-
-
009-079
009-078
-
010-002
010-001
012-071
012-011, 012-
012, 012-013,
012-014, 012-
015
dC330