Xerox DocuColor 2240 Service Manual page 921

Chain-Link Name
744-050 STS-2 Target run temperature#22
DC3535 only
744-051 Environment temperature correction
744-052 STS-1 Low Temp Not-ready Temp
744-053 STS-2 Low Temp Not-ready Temp
744-054 HFSI Counter Index
744-055 STS-1, -2 shift from target run temp#1
DC3535 only
744-056 STS-1, -2 shift from target run temp#2
DC3535 only
744-057 STS-1, -2 shift from target run temp#3
DC3535 only
744-067 STS-1, -2 shift from target run temp#13 5
DC3535 only
744-068 STS-1,-2 shift from target run temp#14 10
DC3535 only
744-069 STS-1,-2 shift from target run temp#15 15
DC3535 only
744-085 Plain Paper S Setting Temperature
744-088 Fuser temp switch - media #3
DC3535 only
744-089 Fuser temp switch - media #4
DC3535 only
744-091 Temp Cont - Auto Dup
DC3535 only
744-092 Temp Cont - Auto Dup
DC3535 only
744-136 Main Lamp delay time
DC3535 only
744-194 Environment Sensor temperature
DC3535 only
744-195 Environment correction working tem-
DC3535 only perature (STS-1, 2)
Initial issue
DC 3535/2240/1632
Table 1 Chain 744
Default Range Description
140 100~200 For optimization of temperature distribution - Transparency SEF (1 bit=1 deg.C).
3 0~5 Environment dependent correction coefficient for level of fusing. Temperature AD value shift amount when the
environment temperature varies 1 degrees Celsius from 20 degrees Celsius. Corrects the target temperature of
Ready temperature/Standby temperature/RUN. Both STS-1 and STS-2 have the same temperature. Corrects
between 10 ~ 20 degrees Celsius. Correction is not performed outside this range. 0=No correction; 1=0.2 degrees
Celsius/Environment Temperature (Maximum 2 degrees Celsius); 2=0.4 degrees Celsius/Environment Tempera-
ture (Maximum 4 degrees Celsius); 3=0.6 degrees Celsius/Environment Temperature (Maximum 6 degrees Cel-
sius); 4=0.8 degrees Celsius/Environment Temperature (Maximum 8 degrees Celsius); 5=1.0 degrees Celsius/
Environment Temperature (Maximum 10 degrees Celsius)
125 100~150 Once the STS-1 reaches Low Temperature Not-Ready Temperature, the Fuser is moved to sagging status to avoid
poor fusing. (1 bit=1 deg.C)
125 100~150 Once the STS-2 reaches Low Temperature Not-Ready Temperature, the Fuser is moved to sagging status to avoid
(1 bit=1 deg.C) poor fusing.
0 0~5 For HFSI Counter Symmetry
5 0~30 Optimization of temperature - plain paper 1 (1 bit=1 deg.C)
10 0~30 Optimization of temperature - plain paper 1 (1 bit=1 deg.C)
15 0~30 Optimization of temperature - plain paper 1 (1 bit=1 deg.C)
0~30 Optimization of temperature - transparency (1 bit=1 deg.C)
0~30 Optimization of temperature - transparency
0~30 Optimization of temperature - transparency
5 0~5 0=Light Weight paper (55~63gsm); 1=Plain paper (64~70gsm); 2=Plain paper (71~80gsm); 3=Bond (81~89gsm);
4=Bond (90~98gsm); 5=Bond (99~105gsm)
5 0~20 Fuser temperature shift qty (-) for plain paper 2
5 0~20 Fuser temperature shift qty (+) for plain paper 2
5 0~10 Plain paper 1 (1 bit=1 deg.C)
5 0~10 Plain paper 2 (1 bit=1 deg.C)
10 0~19 (1 bit=10 msec.)
40 0~80 (1 deg.C/ Environment Sensor temperature read @ power on. Environment controlled based on this factor
bit)
35 20~50 When temperature of STS1/2 is the set value or lower, the environment sensor temperature is read.
(1 bit=1 deg.C)
02/03
6-29
General Procedures and Information
744--xxx Fuser NVM List