Siemens siprotec 7SA522 User Manual page 578

Appendix
Addr. Setting Title
1243 R load (Ø-Ø)
ϕ load (Ø-Ø)
1244
1301 Op. mode Z1
1302 R(Z1) Ø-Ø
1303 X(Z1)
1304 RE(Z1) Ø-E
1305 T1-1phase
1305 T1-1phase
1306 T1-multi-phase
1306 T1-multi-phase
1306 T1-multi-phase
1307 Zone Reduction
1311 Op. mode Z2
1312 R(Z2) Ø-Ø
1313 X(Z2)
1314 RE(Z2) Ø-E
1315 T2-1phase
1315 T2-1phase
1316 T2-multi-phase
1316 T2-multi-phase
1317 Trip 1pole Z2
1317 Trip 1pole Z2
1321 Op. mode Z3
1322 R(Z3) Ø-Ø
1323 X(Z3)
B-6
Function Setting Options
Distance protec- 0.10..250.00 Ohm
tion, general set-
tings
20..60 °
Distance protec-
tion, general set-
tings
Distance zones Forward
(quadrilateral) Reverse
Non-Directional
Inactive
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.00..30.00 sec
(quadrilateral)
Distance zones ( 0.00..30.00 sec
MHO)
Distance protec- 0.00..30.00 sec
tion, general set-
tings
Distance zones 0.00..30.00 sec
(quadrilateral)
Distance zones ( 0.00..30.00 sec
MHO)
0..30 °
Distance zones
(quadrilateral)
Distance zones Forward
(quadrilateral) Reverse
Non-Directional
Inactive
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.00..30.00 sec
(quadrilateral)
Distance zones ( 0.00..30.00 sec
MHO)
Distance zones 0.00..30.00 sec
(quadrilateral)
Distance zones ( 0.00..30.00 sec
MHO)
Distance zones NO
(quadrilateral) YES
Distance zones ( NO
MHO) YES
Distance zones Forward
(quadrilateral) Reverse
Non-Directional
Inactive
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Distance zones 0.05..250.00 Ohm
(quadrilateral)
Default Setting
1; Ohm R load, minimum Load Impedance (ph-
ph)
45 °
PHI load, maximum Load Angle (ph-
ph)
Forward Operating mode Z1
1.25 Ohm R(Z1), Resistance for ph-ph-faults
2.50 Ohm X(Z1), Reactance
2.50 Ohm RE(Z1), Resistance for ph-e faults
0.00 sec T1-1phase, delay for single phase
faults
0.00 sec T1-1phase, delay for single phase
faults
0.00 sec T1multi-ph, delay for multi phase faults
0.00 sec T1multi-ph, delay for multi phase faults
0.00 sec T1multi-ph, delay for multi phase faults
0 °
Zone Reduction Angle (load compen-
sation)
Forward Operating mode Z2
2.50 Ohm R(Z2), Resistance for ph-ph-faults
5.00 Ohm X(Z2), Reactance
5.00 Ohm RE(Z2), Resistance for ph-e faults
0.30 sec T2-1phase, delay for single phase
faults
0.30 sec T2-1phase, delay for single phase
faults
0.30 sec T2multi-ph, delay for multi phase faults
0.30 sec T2multi-ph, delay for multi phase faults
NO Single pole trip for faults in Z2
NO Single pole trip for faults in Z2
Reverse Operating mode Z3
5.00 Ohm R(Z3), Resistance for ph-ph-faults
10.00 Ohm X(Z3), Reactance
Comments