Pickup And Crew Cab Models; Suburban Front Seat - GMC G Service Manual

R/V MODEL TOP STRAP BELT
All hardware discussed in this procedure should be sup­
plied or available from the child seat manufacturer. Be sure
the child seat position does not conflict with any additional
requirements provided by its manufacturer, or with any rec­
ommendations in the Child Restraint section of the Owner's
Manual.
The child seat may be used only in a forward facing
seating location.

PICKUP AND CREW CAB MODELS

1. Place the Child Seat in the front seating position (rear
seating position on crew cab models) (figure 29).
45° :
m a x
Figure 29 — Pickup Top Strap Belt Components
2. Secure the vehicle lap belt over the armrests of the
Child Seat in the position which the Child Seat will
used.
3. Select a suitable anchor bracket mounting location on
the cab back panel. The location must be:
• Located near the rear window reinforcement.
The angle between the Child Seat top strap and
horizontal should not exceed 45°.
• As close to the center line of the Child Seat as
possible, but in no case more than 50 mm (2-
inches) towards the passenger side of the cab,
and 150 mm (6-inches) towards the driver's
side of the cab.
ANCHOR INSTALLATION
156
155. Center Line
156. Window
157. Sealer
158. Anchor Plate
159. Nut
160. Anchor Bracket
161. Bolt
B-09152
• In a position clear of the fuel tank, fuel lines,
brake lines, exhaust systems, etc.
4. Drill an 8 mm (5/16-inch) diameter hole through the
cab panel at the selected location.
NOTICE: See 'Notice'' on page 10A2-1 of this
section.
5. Install the bolt (161), anchor bracket (160), anchor
plate (158), and lock nut (159) to the hole with an
appropriate sealant.
6. Tighten the nut to 31 N»m (23 ft. lbs.). Use the Child
Seat only in the seating position for which the anchor
bracket has been installed, latching the Child Seat top
strap hook to the anchor bracket as shown.
CAUTION: In the event that the Child Seat
anchorage assembly is removed, the 8 mm
(5/16-inch) diameter hole must be properly
resealed to prevent toxic exhaust fumes from
entering the cab.
UTILITY VEHICLE REAR SEAT
1. Determine the location for the anchor by measuring
140 mm (5 1/2-inches) forward from the rear edge of
the floor pan (figure 30). Make this measurement in
the center of one of the depressed floor pan ribs.
Next, measure 1330 mm (52.25-inches) inboard of
the right quarter inner panel. Mark the position where
these measurements meet.
2. Drill an 8 mm (5/16-inch) hole at the mark.
3. To insure proper sealing of the hole, remove any dirt
or foreign matter from around the hole on the under­
side of the floor pan where the sealer is to be applied.
NOTICE: See " Notice" on page 10A2-1 of this
section.
4. Place sealer on the hole from the underside of the
vehicle and assemble the bolt (162), anchor plate
(163), washer (165), and lock nut (166) to the floor
pan.
5. Tighten the nut to 31 N*m (23 ft. lbs.). Use the Child
Seat only in the seating position for which the anchor
bracket has been installed.
NOTICE: In the event the Child Seat anchorage
assembly is removed, the 8 mm (5/16-inch)
diameter hole must be properly resealed.

SUBURBAN FRONT SEAT

This procedure applies to vehicles not equipped with a
second seat or vehicles with the second seat in the down
position.
1. Determine the location for the anchor by measuring
51 mm (2-inches) rearward from the rear edge of the
kick up molding. Make this measurement in the cen­
ter of one of the depressed floor pan ribs (figure 31).
SEATS 10A2-21