Temperature Gage Sensor Replacement; Oil Pressure Gage Replacement - GMC G Service Manual

8C-14 INSTRUMENT PANEL
3. Lens (83).
4. Lens retainer (82).
5. Laminated circuit retaining nuts.
6. Laminated circuit (74) from the retainer (79).
7. Temperature gage retaining nuts (72).
8. Temperature gage (87).
[»♦] Install or Connect (Figure 6)
1. Temperature gage (87) to the laminated circuit.
2. Temperature gage retaining nuts (72).
3. Laminated circuit (74) to the retainer (79).
4. Laminated circuit retaining nuts.
5. Lens retainer (82).
6. Lens (83).
7. Instrument cluster assembly. Refer to "Instrument
Cluster Replacement" in this section.
8. Battery ground cable to the battery.
P-MODELS
Remove or Disconnect
Battery ground cable from the battery.
2. Instrument cluster. Refer to "Instrument Cluster
Replacement" in this section.
3. Lamp socket assemblies.
4. Laminated circuit retaining nuts.
5. Laminated circuit.
6. Cluster case retaining screws.
7. Cluster case from the bezel.
8. Temperature gage retaining bolts.
9. Temperature gage from the cluster case.
[» ♦] Install or Connect
1. Temperature gage to the cluster case.
2. Temperature gage retaining bolts.
3. Cluster case to the bezel.
4. Cluster case retaining screws.
5. Laminated circuit.
6. Laminated circuit retaining nuts.
7. Lamp socket assemblies.
8. Instrument cluster. Refer to "Instrument Cluster
Replacement" in this section.
9. Battery ground cable from the battery.
TEMPERATURE GAGE SENSOR
REPLACEMENT
ALL MODELS
CAUTION: Do not remove cap with the engine
hot. Allow the vehicle to cool off first.
|<"»| Remove or Disconnect
1. Radiator cap.
• Loosen the cap to the first stop. This will relieve
the cooling system pressure.
• Tighten the cap. This will minimize the loss of
coolant when replacing the temperature sender.
2. Sensor harness connector.
3. Sensor.
• Have the new sender ready to install or close
the sender hole with a cork in order to minimize
coolant loss.
[♦ ♦ j Install or Connect
1. Sensor.
2. Sensor harness connector.
3. Coolant (return to the proper level).
OIL PRESSURE GAGE
REPLACEMENT
R/V MODELS
|*-»| Remove or Disconnect (Figure 4)
1. Battery ground cable from the battery.
2. Headlamp switch knob assembly. Refer to CHASSIS
ELECTRICAL(SEC. 8B).
3. Radio control knobs.
4. Clock adjuster stem.
5. Instrument cluster bezel (43).
6. Steering column cover.
7. Instrument cluster lens (42).
8. Transmission shift indicator (41).
9. Retainer (44).
10. Oil pressure gage attaching screws.
11. Oil pressure gage (40).
|-»4|| Install or Connect (Figure 4)
1. Oil pressure gage (40).
2. Oil pressure gage attaching screws.
3. Retainer (44).
4. Transmission shift indicator (41).
5. Instrument cluster lens (42).
6. Steering column cover.
7. Instrument cluster bezel (43).
8. Clock adjuster stem.
9. Radio control knobs.
10. Headlamp switch knob assembly. Refer to CHASSIS
ELECTRICAL(SEC. 8B).
11. Battery ground cable to the battery.
G-MODELS
|*"»[ Remove or Disconnect (Figure 6)
1. Battery ground cable from the battery.
2. Instrument cluster assembly. Refer to "Instrument
Cluster Replacement" in this section.
3. Lens (83).
4. Lens retainer (82).
5. Laminated circuit retaining nuts.