Two-Position Switch; Additional Accessories, Replacement Parts; Model Templates In Detail; Fixed-Wing Model Aircraft - Multiplex Royal SX 9 Instructions Manual

ROYAL SX

Two-position switch

The two-position switches with the Order No. # 7 5750
can be installed in the wells P and / or K. Once in-
stalled, they must be connected to the appropriate
sockets on the left or right corner unit:
Corner unit with socket for switches P and K
(illustration shows switch P)
The switches can be used directly as controls P and /
or K in the menus ¡Assignment, Switches and
¡Assignment, Controls. No software assignment
is required for the Extra Sw.
20.5.4.

Additional accessories, replacement parts

aluminium stick top, long, with push-
# 8 5942 button
aluminium stick top, long, with two-
# 8 5941 position switch
aluminium stick top, long, with three-
# 8 5940 position switch
# 7 5308 aluminium stick top, long
# 7 5305 stick top, short, black
# 7 5306 stick top, short, orange
# 7 5300 Stick units short
# 7 5301 Stick units medium
# 7 5302 Stick units long
# 7 5303 stick units long, with push-button
# 8 5307 transmitter tray
# 8 5640 "Cross-over" transmitter support strap
# 8 5148 USB PC lead
# 763323 Transmitter case
# 7 5750 two-position switch, ON/OFF, short
# 4 5183 Trainer mode operations stick
# 4 5185 Souffleur DE
# 4 5186 Souffleur EN
# 4 5182 Telemetry Display
# 8 6020 charge lead
# 8 5147 MULTIflight Stick
For more information on accessories and replacement
parts please refer to the current main catalogue, or
our Internet website: www.multiplex-rc.de.
94
21.

Model templates in detail

21.1.

Fixed-wing model aircraft

!
The next two steps must always be carried out
when you are setting up a new fixed-wing model:
a. Check stick functions (aileron / elevator / rudder).
Select different stick mode if necessary:
L, Assignment, Mode
b. Check direction of servo rotation for all functions
Reverse servo directions if necessary (REVERSE):
K, Calibrate, select servo,
Parameter á.
Note regarding V-tail models:
If your model is fitted with a V-tail, change the As-
signment in the menu K Servo as follows:
Elevator or ELEVATR+
replace with V-TAIL+,
Rudder
replace with V-TAIL+.
!
The descriptions in the model templates will
only be correct if the mixer definitions and the
transmitter control and switch assignments still
match the factory default settings.
Details in the model template descriptions.
The following points are listed in the descriptions:
Suitable for:
Model category, and several models as examples of
what can be operated using the template in question.
Assigned transmitter controls and switches:
Transmitter control and switch functions assigned by
default. The standard settings are as follows:
Transmitter Controls to 100%,
D/R (Dual Rate) to 100%,
Expo to 0%.
Assigned servos / receiver outputs:
What is controlled using which receiver output or
servo. When setting up a New model you can choose
any of four different servo configurations.
!
To avoid the illustrations becoming too clut-
tered, the four possible assignments are grouped
together in the summary ( 21.3.) "Servo configu-
rations".
Timer settings:
How the Timers in the model template are prepared,
and the method of controlling them.
Additional functions:
E.g. Tow rel. in the model template GLIDER.
Fine-tuning:
What must and can be checked or adjusted when you
are setting up a model in the model memory.
Mixers:
Summary of the default Mixer facilities.