Setting Up A Model Helicopter; The Method In Principle; Setting Up A New Model In The Transmitter45; Menu I, Call Up New Model - Multiplex Royal SX 9 Instructions Manual

13.

Setting up a model helicopter

13.1.

The method in principle

In our example we will set up a model memory for a
helicopter with 120° CCPM rotor head and electric
power system.
The following steps are necessary to ensure that the
model's working systems operate correctly:
a. Set up a new model in the transmitter
b. Prepare the transmitter controls / switches 13.3.
c. Check / change the servo assignment
d. Check and adjust the main rotor
e. Check and adjust the tail rotor
Once you have completed these five steps, you will be
able to control the model's basic functions - roll, pitch,
yaw and throttle / collective pitch.
At this point we can expand and refine the set-up:
f. Working with flight phases
Assign switches
Unlock / lock / name flight phases
Set up transition times
Set the correct values.
Setting up a New model in the
13.2.
transmitter

Menu I, call up New model

13.2.1.
a. Open the main menu Memory:
Press button I.
b. Open the menu New model:
Turn the 3-D digi-adjuster to the right as far as New
model, and open the menu
(press the 3-D digi-adjuster):
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
Note:
The definition of the model is not complete until you
confirm your selected settings with OK ( 13.2.7.).
13.2.2.

Which model memory will be used?

New models are automatically stored in the trans-
mitter's first vacant model memory: the memory num-
ber appears in the menu. Since you have no influence
over the memory number, this line in the menu is
skipped.
13.2.
13.4.
13.5.
13.6.
13.10.
 13.2.2..
3
 13.2.3.
HELIccpm
 13.2.4.
MPX-UNI
 13.2.5.
2: è é
 13.2.6
HELI
 13.2.7
If all the memories are occupied, the screen displays:
Memory nr.
If you nevertheless attempt to set up the new model,
the following on-screen warning appears:
No memory free
Press ENTER
13.2.3.

Selecting the template

Note:
The model templates ( 11.5.) make it much easier
and quicker to set up new models, as they already
contain the essential assignments and adjustments.
You can check which template was used to create a
particular model by accessing the menu ¦Memory,
Properties.
Turn the 3-D digi-adjuster to the right until the select
bar stands in the Template line, then press the 3-D
digi-adjuster.
Now you can select the template HELIccpm from the
eight available templates, using the 3-D digi-adjuster:
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
Press the 3-D adjuster once more to confirm your choice.

Selecting the servo config(uration)

13.2.4.
Note:
The servo configuration ( 11.6.) defines the order in
which the servos in the model have to be connected
to the receiver. The selected configuration is only a
suggestion, and can be changed subsequently in any
way you wish if the servos are connected to different
receiver outputs ( Menu: ¤, Assignment).
Rotate the 3-D digi-adjuster to the right until the select
bar is at the Servo conf. line, then press the 3-D
digi-adjuster.
Now use the 3-D digi-adjuster to select the MPX-UNI
configuration from those available:
¦New model
¨Exit
Memory nr.
Template
Servo conf. MPX-UNI_
Mode 4:
Assignment HELI
OK
Press the 3-D adjuster again to confirm your choice.
Manual
-1
3
HELIccpm
MPX-UNI
4: è é
HELI
3
HELIccpm
è é
45