Setting Up A Fixed-Wing Model; The Method In Principle; Setting Up The New Model In The Transmitter; Menu I, Call Up New Model - Multiplex Royal SX 9 Instructions Manual

ROYAL SX
12.

Setting up a fixed-wing model

We recommend that you first read Chapter 11, which
describes the operating philosophy of the ROYAL SX,
before you set up a new model in a memory. This
should ensure that you have at least a basic under-
standing of the system, and will be able to carry out
the following steps more easily.
12.1.

The method in principle

In this example we will set up a model memory for a
glider with a four-flap wing.
The following steps have to be carried out to ensure
that the model's basic functions work as expected:
a. Set up new model memory
b. Prepare transmitter controls and switches 12.3.
c. Prepare servos
d. Activate and check mixed functions
Example: ailerons raised as landing aid.
After these four steps you will be able to control the
model's basic functions, i.e. aileron, elevator, rudder
and throttle. Butterfly (Crow) is activated as landing
aid.
At this point you can expand and refine the set-up:
e. Activate Combi-Switch
f. Set up aileron differential
g. Elevator trim mixers
spoiler / throttle to elevator mixers
h. Activate the inboard wing flaps
i. V-tail model
j. Working with flight phases
Assign switch
Unlock / lock / name phases
Set transition times
Adjust values
k. Further options that can be added
Dual-Rate (D/R), Expo,
Combi-Switch, Motor run timer.
12.2. Setting up the new model in the
transmitter

Menu I, call up New model

12.2.1.
a. Open the main menu Memory:
Press button I.
b. Open the menu New model:
Turn the 3-D digi-adjuster to the right as far as New
model, and open the menu
(press 3-D digi-adjuster):
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
32
12.2.
12.4.
12.5.
12.11.2.
12.6.
12.7.
12.8.
12.9.
12.10.
12.11.
 12.2.2.
3
 12.2.3.
4 FLAPS
 12.2.4.
MPX-UNI
 12.2.5.
4: è é
 12.2.6.
GLIDER
 12.2.7.
Note:
The new model is not stored in the memory until you
confirm the selected settings with OK ( 12.2.7.).
12.2.2.

Which model memory will be used?

New models are automatically stored in the first va-
cant memory; the memory number appears in the
menu. Since you have no influence over the memory
number, this line in the menu is skipped.
If all model memories are in use, the screen displays:
Memory nr.
If you nevertheless attempt to set up the new model,
the following on-screen warning appears:
No memory free
Press ENTER

Selecting the Template

12.2.3.
Note:
The templates ( 11.5.) make it much quicker and
easier to create new models, as they already contain
the essential assignments and settings. You can
check which template was used to create a particular
model by accessing the menu ¦Memory, Properties.
Turn the 3-D digi-adjuster to the right until the select
bar stands in the Template line, then press the 3-D
digi-adjuster.
Now you can select the template 4 FLAPS from the
eight available templates, using the 3-D digi-adjuster:
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
Press the 3-D adjuster once more to confirm your
choice.
12.2.4. Selecting the servo configuration (servo
conf.)
Note:
The servo configuration ( 11.6.) defines the order in
which the servos have to be connected to the receiver
in the model. The selected configuration is only a
suggestion, and can be changed subsequently in any
way you wish if the servos are connected to different
receiver outputs ( Menu: K, Assignment).
Rotate the 3-D digi-adjuster to the right until the select
bar is at the Servo conf. line, then press the 3-D
digi-adjuster.
-1
3
4 FLAPS
MPX-UNI
4: è é
GLIDER