Entering The Model Name; Preparing The Controls / Switches; Checking / Changing Control Settings For Idle / Collective Pitch Min. And Throttle Limiter Min - Multiplex Royal SX 9 Instructions Manual

b. Transmitter control assignment
Roll, pitch, yaw (aileron, elevator, rudder) and collec-
tive pitch are defined by the stick mode which you se-
lected in step ( 13.2.5.).
!
Important: do not assign a throttle control!
The model helicopter's throttle is always controlled by
the collective pitch stick, so you must not enter any-
thing under Throttle in the menu Setup, Assign-
ment, Controls.
Throttle
The throttle settings are entered under Throttle in the
Transmitter control menu.
In the menu L Assignment, Controls you will find:
Function Control
Throttle --- -
#* Left slider for gyro gain
Gyro E
Collect. ‡ #
Thr.limit F #*
Transmitter controls not in use are marked in the assign-
ment list with " --- - ", and are not listed here.
c. Switch assignment
In the menu L Assignment, Switches you will see:
Function Switch
DR-ai <L #
DR-el <L #
DR-ru <L #
CS/DTC <N #
Throttle-cut H> „
´ Sum F '
Main phase I> #
'* Flight phase switch
Phases 1-3 <O
Switches not in use are marked in the assignment list with
" --- - ", and are not listed here

Tip: you can now carry out an initial check of the
working systems using the servo monitor; you don't
need the model for this. Move to the monitor as fol-
lows:
Menu ¤Servo, Monitor:
Bar graph
Move the sticks, sliders and switches and watch the
effects on-screen.
When you access the Monitor menu you will see the
bar graph display. Rotate the 3-D digi-adjuster to toggle
between the two types of display. Press the 3-D digi-
adjuster to leave the servo monitor.
--- -
Assign nothing!
Dual-Rate
Aileron, elevator and rudder are
switched simultaneously
DTC = Direct Throttle Control
(and CS = Combi-Switch
for fixed-wing models)
With momentary function
Aggregate timer, motor run
controlled by Control F
(throttle limiter)
Switch for main flight phase
Percentage values
13.2.8.

Entering the model name

The model you have just stored initially bears the
name of the template you are using. In our example
this would be HELIccpm. To help you keep track of
your models, you should change this default name to
the actual model name.
This is the procedure:
a. Open the main menu ¦Memory
(press button I).
b. Select the Properties menu and open it:
¦Memory
¨Exit
Select model ....
Copy
Erase
Flight phase ....
Properties
ªNew model
(Select using the 3-D digi-adjuster, then press).
c. Use the 3-D digi-adjuster again to select the Name
line, then press ENTER (or the 3-D digi-adjuster):
¦Properties
¨Exit
Template HELIccpm
Mode 3: è é
Assignment HELI
Name Heli 600
At this point you can enter a model name with a
maximum of sixteen characters; it should clearly
identify the model. This name will also appear in
the Status display.
Text input using the keypad ( 11.1.1.).
13.3.

Preparing the controls / switches

13.3.1. Checking / changing control settings for
idle / collective pitch min. and throttle
limiter min.
a. Idle / Collective pitch min.
In the Helicopter templates Idle / collective pitch
min. is set to "back"
(# arrow following the code letter).
b. Throttle limiter
By default the minimum position for the throttle
limiter is also set to "back".
This is the procedure for changing it to "forward":
Move to the menu ¡Setup, Assignment (e.g.
Coll. Pitch (Collect.)), and search for the trans-
mitter control to be changed:
Collect.
Press ENTER to open the menu point.
This change is "global" in effect, i.e. it affects all
models which are set up to use the HELI assign-
ment list. For this reason you must confirm the
warning message by pressing ENTER.
Collect.
Move the stick to the desired position for Idle / Col-
lective pitch min.:
Collect.
Manual
....
....
....
....
‡ #*
‡ #
‡ '*
47