Selecting The Stick Mode; Selecting The Assignment; Confirming With Ok - Multiplex Royal SX 9 Instructions Manual

Now use the 3-D digi-adjuster to select, for example,
the MPX-UNI configuration from those available:
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
Press the 3-D adjuster again to confirm your choice.
By selecting the 4 FLAPS template and the servo con-
figuration MPX-UNI you automatically set the following
receiver output sequence:
MPX-UNI
1
AILERON+
2
ELEVATR+
3
Rudder
4
Throttle
5
AILERON+
6
FLAP+
7
FLAP+
8
Spoiler
9
Spoiler
See also the illustration in ( 12.2.7.).

Selecting the stick mode

12.2.5.
The stick mode defines the association between the
stick axis and the controlled function. However, the
mode affects only the functions aileron, elevator and
rudder. The way in which throttle, spoiler and flap
are controlled is defined when you assign the transmit-
ter controls ( Menu: L, Assignment, Controls).
First consider the functions you wish to control using
the left stick, then look up the appropriate mode in
the table below.
Mode table for the left stick:
Stick movements, left stick
forward/back left/right
Rudder
Elevator
Aileron
Rudder
Throttle
(or Spoiler)
Aileron
The double arrows following the mode code numbers
indicate where elevator (
cated.
The stick functions for the right stick are assigned
automatically.
Example: we will assume that you want elevator and
aileron on the left stick; in which case you would se-
lect Mode 3. Rudder is now automatically on the right
stick.
Turn the 3-D digi-adjuster to the right until the select
bar is over the Mode line, then press the 3-D digi-
adjuster:
3
4 FLAPS
MPX-UNI_
4: è é
GLIDER
Required
mode
1: è é
3: è é
2: é è
4: è é
è é
) and rudder ( ) are lo-
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
You can now use the 3-D digi-adjuster to select the
stick mode you have just decided to use.
Press the 3-D digi-adjuster to confirm your choice.

Selecting the Assignment

12.2.6.
At this point you can select the assignment list, which
defines which transmitter controls and switches are
used to operate the various functions.
For a glider you would of course use the assignment
list bearing the name GLIDER (No. 2).
Turn the 3-D digi-adjuster to the right until the select
bar is over the Assignment line, then press the 3-D
digi-adjuster:
¦New model
¨Exit
Memory nr.
Template
Servo conf.
Mode
Assignment
OK
Select GLIDER from the five available assignments
using the 3-D digi-adjuster.
Press the 3-D digi-adjuster to confirm your selection.
Note:
You can also change the selected assignment in any
way at any time (Menu: ¡Setup, Assignment).

Confirming with OK

12.2.7.
Rotate the 3-D digi-adjuster to the right until the select
bar is at the OK line, then press the 3-D digi-adjuster.
Congratulations!
You have successfully stored a new model in the
transmitter's memory.
If you have kept to our suggestions in the steps com-
pleted thus far, the following data is now stored in the
new model memory:
a. Receiver output sequence
Spoiler
8
1
AILERON+
6
FLAP+
3
2
Rudder
ELEVATR+
4
Throttle
Fig. 12.2.7.1.: Servo assignment with MPX-UNI configuration
Manual
3
4 FLAPS
MPX-UNI
4: è é
GLIDER
3
4 FLAPS
MPX-UNI
4: è é
GLIDER__
Spoiler
9
7
FLAP+
5
AILERON+
33