Switching On, Using The Transmitter; Switching On For The First Time; Switching On "Normally; Rf Module Excl. Scanner Installed - Multiplex Royal SX 9 Instructions Manual

ROYAL SX
10. Switching on, using the
transmitter
!
The ROYAL SX is supplied with the transmitter
battery partially charged. The pack must be fully
charged before you use the transmitter. Please refer
to the charging notes ( 8.).
10.1.

Switching on for the first time

The very first time you switch the ROYAL SX trans-
mitter on is a special case. When switched on, the
transmitter displays the following menu:
ROYAL SX16
Select language:
Sprache wählen:
skip/später
English
Deutsch
In this menu you select the language which the trans-
mitter will use for the menus and the names of the
pre-defined mixers and assignment lists. We recom-
mend that you select the appropriate language when
you first switch the transmitter on:
Select the appropriate language using the ▲ and ▼
buttons, then press ENTER to confirm your choice.
If you select English:
a. English will be used as the menu language.
b. The pre-defined mixers are defined using English
terminology:
ELEVATR+, AILERON+, ...
The mixer inputs are also described in English:
Aileron, Elevator, Rudder, ...
If you change the selected language to German
(Deutsch) in the menu Setup, User, then the
names of the pre-defined mixers will continue to
appear in English, but the German terms will be
used for the mixer inputs:
Quer, Höhe, Seite, ...
It is possible to change the names of all the four-
teen free mixers to anything you like (Name pa-
rameter). This is accomplished in the menu Setup,
Mixer def..
Deutsch
If you select (German):
a. German will be used as the menu language.
b. The pre-defined mixers are defined using the
German terminology:
HÖHE+, QUER+, ...
The mixer inputs are also described in German:
Quer, Höhe, Seite, ...
skip/später
If you select
a. English will be used as the language.
b. Next time you switch on, the same menu will ap-
pear, and you can repeat the language selection.
22
3.46 DE/EN
Only these
buttons are
active!
▲  
ENTER
(not recommended):
10.2. Normal Operations
This is the procedure for operating your ROYALevo,
ROYAL SX or ROYAL SX M-LINK transmitter in nor-
mal mode:
1. Switch the ROYALevo, ROYAL SX or ROYAL SX
M-LINK transmitter ON:
 The red LED on the transmitter flashes once
every two seconds.
2. Switch the M-LINK receiver ON.
The M-LINK system is now ready for use.
10.3.

RF module excl. Scanner installed

The 2.4 GHz ISM band offers the facility to transmit
model data back to the transmitter. If you are using
a telemetry-capable M-LINK receiver, the actual volt-
age of the receiver power supply will be displayed di-
rectly on the integral screen of your ROYALevo,
ROYAL SX or ROYAL SX M-LINK transmitter. If the
battery voltage falls below a certain threshold, the
transmitter also emits an audible signal to warn you
that the receiver battery is almost flat.
For more information on this feature, please refer to
the operating instructions supplied with your teleme-
try-capable M-LINK receiver.
10.4. Switching the transmitter on
with throttle-check active
Throttle-check is a safety function. If you are about to
fly a powered model, the throttle check (throttle lock)
prevents an electric motor bursting into life unexpec-
tedly if you switch the system on when the throttle
channel is not at idle.
You will find the parameter Check Thr. in the menu:
Setup, Transmitter:
¡Transmitter
¨Exit
Sound
Safety
Check Thr.
Check RF
The factory default setting is ON. The conditions for
throttle-check are different for fixed-wing model aircraft
and helicopters; for this reason they are described
separately in the next two sections.
10.4.1.

Throttle-check for fixed-wing models

This warning appears if:
 Throttle-Check (Check Thr.) is set to ON (see above)
and
 the throttle control is not in the idle position (or at
the motor OFF position)
and
All
ON_
ON
Indicator for
throttle control
(throttle stick
in this case)