Acura 1994 Integra Service Manual page 30

Standards and Service Limits
Differential (Manual transmissionl
Section 15
Differential (Automatic transmissionl
Section 15
Steering - Section 17
' When using a new belt, adjust detlection or tension to new values. Run the engine lor 5 minutes then turn it off.
Readiust detlection or tension to used belt values.
M€ASUREMENT
STANDARD INEW) SERVICE LIMIT
Differential Pinion shaft contact area LD.
81881 engine
8 1 8 C 1 e n g i n e
Carrier'to-pinion clearance 81881 engine
B18C t engine
Driveshafvintermediate shaft contact area LD.
8 1 8 8 1 e n g i n e
818C1 engine
Carrier to driveshaft clearance 81881 engine
BlSC'l engine
Carrier-to-intermediate shatt clearance
B188l engine
818C1 engine
18.000 - 18.016 (0.7087 - 0.7093)
18.000 18.018 (0.7087 - 0.7094)
0.0r3 0.045 (0.0005 - 0.0018)
0.0'13 - 0.047 (0.0005 0.0019)
28.000 - 28.021 \1.1024-1.10321
28.005 - 28.025 (1.1026 1.'1033)
0.020 - 0.062 (0.0008 0.0024)
0.045 , 0.086 {0.0018 - 0.0034)
0.050 - 0.087 (0.0020 0.0034)
0.075 - 0.111 (0.0030 - 0.0044)
o. t aron,
0.1 {0.006}
Differential
prnron gear
Eacklash
t . D .
Pinion geaFto-pinion
shaft clearance
0.05 0.15 (0.002 0.006)
'18.042 - 18.066 (0.7103
0.7113)
0.055 - 0.095 (0.0022 0.0037)
Adjust
0.15 {0.006)
Sel ring-to-bearing outer race clearance
81881 engin€
0 - 0.10 (0 0.004)
Adjust
Differential taper roller bearing preload
Starting torque N.m {kgfcm, lbf.in) Bl8Cl engine
2.1r - 3.04 {21.5 - 3 r.0, 13.0- 18.7)
Adjust
MEASUREMENT
STANDARO INEWI SERVICE LIM]T
Difterential
carfl€r
Pinion shatt contact area l.D.
Carrier-to-oinion clearance
Driveshafvintermediate shaft contact are l.D.
Carrier-to-driveshatt clearance
18.000 - 18.018 {0.7087 - 0.7094)
0.016 - 0.052 {0.0006 - 0.0020)
28.00s 28.025 {1.1026 - 1.1033)
0.025 - 0.066 (0.0010 - 0.0026)
0.1 {0.004)
0.12 (0.005)
Differential
prnron gear
Backlash
t.D.
Pinion gear-to-pinion
shaft clearance
0.05 - 0.15 (0.002 - 0.006)
18.042 - 18.066 (0.7r03 - 0.7113)
0.059 - 0.095 (0.0023 - 0.0037)
Adjust
0.15 (0.006)
Set ring-to-bearing outer race clearance
0 - 0.r5 (0 - 0.006)
Adjust
MEASUREMENT STANDARD INEWI
S t e e r i n g w h e e l
Rotational play at steering wheel circumference
Staning losd at steering wheel circumference
N {kgf, lbfl Engine running
0 - 10 {0 - 0.39)
3 4 \ 3 . 5 , 7 . 7 1
Gearbox Angle of rack-guide-screw loosened from locked
position
20" i 5'
Purnp
Pump pressure with shut-off valve closed
kPa (kgtlcm,, psi)
6,400 7.400 165 75. 920 - 1. r00)
Power steering
tluid
Recommended fluid
Fluid capacity For overhaul
f (US qt, lmp q0
For fluid change
Honda power steering fluid V
1 . 0 6 ( 1 . 1 2 , 0 . 9 8 )
0.79 (0.83,0.70)
Power steering
belt*
Deflection with 98 N (1okgt,22lhfl
between pulleys
11.5- 13.5 (0.45 0.53)with used belt
8.0 - 10.010.31 0.39)with new belt
Belt tension N lkgf, lbl)
Measured with belt tension gauge
390 - 540 (40 - 55, 88 - 120) with used belt
740 880175 90. 170 200) with new belt