Auerswald COMpact 5010 VoIP Configuration Manual page 44

Features – Function and Configuration
Call Distribution and Reachability
– – –
HW requirements
SW requirements Version 3.8AC (PBX)
Version 4.2A (system telephone COMfortel
...)
Version 2.6.0 (COMfortel Set)
Dongle release – – –
Configuration via / COMset
Setting via (scr)
scriber selection in the list field at the top
COMset
connections
COMset
nections
nection
COMset
nections
nection
COMset
IP (VoIP)
nection
COMset
IP (VoIP)
nection
COMset
GSM Routing
System telephone
For explanations concerning the table, see
Configuration of the Feature
Call forwarding for ISDN DDIs may be configured under COMset
External numbers ISDN connections
connection.
Call forwarding for ISDN MSNs may be configured under COMset
External numbers ISDN connections
connection.
Call forwarding for analogue telephone numbers may be configured
under "COMset External numbers
Forwarding".
Call forwarding for VoIP DDIs may be configured under COMset
External numbers Voice over IP (VoIP)
PTP connection.
Call forwarding for VoIP MSNs may be configured under COMset
External numbers Voice over IP (VoIP)
PTMP connection.
You can set each port so that call forwarding may be configured by
the network provider (not in case of VoIP) instead of using the PBX
(2nd call channel, COMset
ing ...). Configuration via the user's telephone stays the same. It is
possible that the configuration may take more time (time to acknowl-
edgement).
The delay time configured for the call forwarding "on no reply" via the
PBX (2nd call channel) may be changed per port (COMset
External numbers ... Call Forwarding
call forwarding configured in the central office is fixed to 20 seconds.
The default configuration for call forwarding for MSNs and DDIs via
the PBX (2nd call channel) is the call channel on the same port (e.g.,
because the charges for different S
persons). Since the probability is higher that call forwarding may not
be executed due to a busy call channel, you can change this setting
dependent on the port and authorize any call channel (COMset
External numbers ... Call Forwarding
44
Features – Function and Configuration
Internal numbers Subscriber
Properties Authorizations + sub-
External numbers Analogue
Call Forwarding
External numbers ISDN con-
Call Forwarding PTMP con-
External numbers ISDN con-
Call Forwarding PTP con-
External numbers Voice over
Call Forwarding PTMP con-
External numbers Voice over
Call Forwarding PTP con-
External numbers VoIP /
Exception number
Call Forwarding
Call Forwarding
Analogue connections
Call Forwarding
Call Forwarding
External numbers ... Call Forward-
...). The delay time for
ports are assigned to different
0
...).
The routing can also be done depending on the destination number.
Routing must be activated for this (COMset
Call Forwarding
Call Through list (COMset
ing Exception number).
Individual subscribers can be restricted from configuring call forward-
ing for external numbers using a telephone (COMset
bers Subscriber (scr)
selection in the list field at the top).
On a system telephone COMfortel 1100/1500/2500/2500 AB/VoIP
2500 AB, a function key can be configured for call forwarding for
external numbers (see the manual for the telephone).
Use/Check of Features
1. Configure call forwarding.
2. Call the forwarded number.
3. Depending on the type of call forwarding activated, the call should
reach the target configured.
Dependency/Limitations
After a firmware update with firmware version 3.8, it is also possible
to set call forwarding for external telephone numbers as
configuration-dependent. For situations where your settings are
supposed to apply even after configuration switchovers, you can use
the so-called permanent configuration. If permanent configuration is
enabled, the configuration-dependent settings will be overridden by
the permanent configuration settings.
On a system telephone COMfortel 1100/1500/2500/2500 AB/VoIP
2500 AB, you can switch on/off/over the call forwarding of external
numbers either for the current configuration or for permanent config-
page 39
uration using the function key (see the manual for the telephone).
With a standard telephone you can change call forwarding in the per-
manent configuration and switch on the permanent configuration or
the current configuration using a digit sequence. As soon as every
call forwarding has been switched off in the permanent configuration,
the permanent configuration for the corresponding telephone number
PTP
is switched off and the configuration-dependent settings apply. Tip:
To override the configuration-dependent settings with no call forwar-
ding, enable call forwarding in the permanent configuration without
PTMP
specifying a destination number.
If you would like to forward calls to a T-Net Box, network provider
must release call forwarding.
Call
For call forwarding on busy to an analogue connection via the
network provider, the following applies: The central office only
detects whether the analogue connection is busy. The central office
does not detect whether the telephones being called are busy. This
means the following:
As soon as the analogue connection becomes busy, call forwarding
on busy is also carried out. This also occurs when internal
subscribers that are set to accept the calls for this connection during
normal call distribution are available.
Even if the analogue connection is available, but the internal
subscriber that is set to accept calls on this connection during normal
call distribution becomes busy, no call forwarding on busy is carried
out.
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
External numbers
...) and the destination number recorded in the
External numbers VoIP / GSM Rout-
Properties Authorizations + subscriber
...
Internal num-