Auerswald COMpact 5010 VoIP Configuration Manual page 20

Configuration Manual
Configuration Manual
Example 1: Basic Configuration with Internal Subscribers and Call Distribution
Voice-over-IP (VoIP)
Up to 10 accounts can be configured in the COMpact 5010 VoIP and
up to 20 accounts in the COMpact 5020 VoIP. The PBX supports two
different types of VoIP account:
VoIP accounts with one or more VoIP phone numbers (similar the
Point-to-Multipoint connection on ISDN)
VoIP accounts with a DDI number block (similar to the -PBX con-
nection on ISDN) based on the SIP-DDI feature (also known as
SIP trunking)
To receive the necessary access data, accounts must first be set up
with one or more VoIP providers. For this purpose, you need to reg-
ister your name and address with a provider via their web site. Then
a telephone number accessible from the land line network and the
VoIP Provider
In the PBX, you can configure the VoIP pro-
viders with which you have accounts.
To do this, open the page displayed in the fig-
ure to the right.
Frequently-used VoIP providers and their
configurations are already provided as default
providers in the system. If you would like to
use them, activate them as follows.
Under "Action", activate the default providers
and then click "Execute".
If your provider is not one of the default pro-
viders, configure your provider as follows.
Under "Provider name", enter any name with
a maximum of 16 characters. Then click "Exe-
cute".
Click "Configure" next to the names entered.
Configure the settings for the provider. You will receive the data
directly from the provider or over the corresponding lists on the Inter-
net. For more information, also refer to the online Help COMset
External numbers Voice over IP (VoIP)
Then click "Execute" to apply the settings to the PBX.
VoIP Accounts
In the PBX, configure the VoIP accounts you
have available.
To do this, open the page displayed in the fig-
ure to the right.
Under "Provider name", select the desired
account provider from the list field.
Under "Account name", enter any name with
a maximum of 16 characters.
Under "Kind of connection" and depending
on the available telephone numbers, select
the kind of VoIP account from the list field.
For VoIP accounts with one or more VoIP
phone numbers, select "PTMP connection".
For VoIP accounts with a DDI number block based on the SIP-DDI
feature (also known as SIP trunking), select "PTP connection".
Click "Execute" to accept the settings in the PBX.
Click "Configure" to configure the VoIP account.
20
Internet as well as an account with a user name (is also known as the
user name, authorization user and SIP ID) and password are
assigned. Most of the time, the registered connection is set up within
just a few minutes and can be used almost immediately.
Note: In order to resolve the names of Internet addresses, the PBX
needs (just like with a PC connected to the Internet) the address for
a DNS server. This means that the address provided by your system
administrator or by your Internet service provider needs to be
entered. You may also enter a second address just in case the main
DNS server is unavailable. If you have not configured this setting dur-
ing the initial system set-up using the configuration assistant, you can
now do it using the information found on the page Administration
Server configuration.
The figure shows you the following page with the settings for
COMset External numbers
Then click "Back".
The provider is now configured.
If additional providers are required, enter additional names under
"Provider name" and configure the settings for them.
Provider.
Click the "Online configurations" button to download provider con-
figurations supported by Auerswald from the Internet.
The figure shows you the following page with the settings for
COMset External numbers
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
Example 1 on page
Voice over IP (VoIP) Provider
Example 1 on page
Voice over IP (VoIP) Accounts
12:
12: