Cti - Computer-Assisted Telephony; Lan-Tapi - Auerswald COMpact 5010 VoIP Configuration Manual

LAN-TAPI

The Auerswald LAN-TAPI function offers the TAPI 2.1 interface via
Ethernet port on the PBX.
A Microsoft server connected with the interface distributes this func-
tionality on the network (third party network connection) to individual
Microsoft computers so that telephony software, e.g., ESTOS ProCall
or also other TAPI applications may use TAPI functions. The PBX is
connected to the server over the Ethernet interface. If the user wants
to dial from the client PC, this command is transferred to the server.
The server transports the command to the PBX that establishes the
connection finally.
TCP/IP network with
HW requirements
CTI server and CTI clients (Microsoft
domain structure)
SW requirements Version 3.0C (PBX)
Version 2.3E (system telephone COMfort
...)
Version 3.6C (system telephone COMfor-
tel ...)
CTI software (e.g., from Estos) and corre-
sponding server software (if necessary,
consult the software vendor for the CTI
software used)
Dongle release Release of the TAPI subscribers necessary
Configuration via / COMset
Setting via
COMset
LAN TAPI subscriber
COMset
figuration
Administration
For explanations concerning the table, see
Configuration of the Feature
Release the desired number for TAPI subscribers using the required
release code (Administration
All subscribers that are to be controlled over a PC must be selected
on the page COMset Functions
scriber.
The port and the password must be configured for the network con-
nection to the TAPI server. The password may not start with a zero.
(COMset Functions LAN TAPI
The PBX must be connected to a server PC over a TCP/IP network.
The TAPI driver (TSP) for the PBX must be installed on this server
PC. Use the driver located on the accompanying Auerswald Mega
Disk (Version 5.95 or later) or use – if available – a newer version
from the Auerswald Web site. Proceed as follows:
1. Start the Auerswald Mega Disk on the server PC.
2. Open the software page for the COMpact 5010/5020 VoIP and
click "TAPI service providers" under "Drivers".
The TAPI driver installation is started.
3. Follow the installation by clicking "Next".
4. In the "IP address of the PBX" entry field, enter the IP address of
the PBX.
5. Enter the network port of the TAPI server in the "Port" entry field
(recommended 7001).
6. Enter the password (6 to 8 characters) for the network connection
of the TAPI server in the "Password" and "Repeat password" entry
fields.
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
Features – Function and Configuration
CTI – Computer-assisted Telephony
General settings CLIP texts
Functions LAN TAPI
Functions LAN TAPI
Dongle releases
page 39
Dongle releases).
LAN TAPI LAN TAPI sub-
Configuration)
7. Click "OK".
8. Click "Close".
9. Restart the Server.
For all additional settings and installations (on the server and the cli-
ent), consult the vendor of the CTI software used.
Operation/Check of the Feature
For a simple function check of the TAPI driver (TSP) as well as of the
settings done in the PBX, you can use the Windows dialer on the
server PC. Proceed as follows:
1. Start the Windows dialer by executing "dialer.exe".
2. Select one of the offered telephones for controlling. The telephone
selected here must also be entered on the page COMset
tions LAN TAPI
Con-
with Windows 2003
Features – Function and Configuration
CTI – Computer-assisted Telephony
LAN TAPI subscriber.
Func-
91