Auerswald COMpact 5010 VoIP Configuration Manual page 22

Configuration Manual
Configuration Manual
Example 1: Basic Configuration with Internal Subscribers and Call Distribution
tions. To do this, the PBX gives you the option of configuring diver-
gent call distribution. This configuration is done in two steps. In the
first step, the PBX is notified which telephone numbers are to be
taken out of the linear call distribution. In the second step, the tele-
phone numbers are directly assigned internal subscribers.
Distributing Calls on the analogue Connection
In the PBX, configure the associated internal
telephone number for the registered tele-
phone number.
To do this, open the page displayed in the fig-
ure to the right.
Under "Call distribution for ...", select from
the list field „Analogue connections".
Under "Analogue connection", select from
the list field one of the already configured ana-
logue connections.
The telephone number for this connection is
displayed under "Telephone number |
name".
Under "Internal no. | name", select an inter-
nal telephone number for the external tele-
phone number from the list fields.
If the external telephone numbers should also
be used as fax numbers and the calling fax
machine should automatically be detected,
configure the following settings
"Modem/fax call distribution":
Select the "Fax" setting from the list field. (Select "Fax and modem"
if a modem should also be detected.)
Under "Detection duration", select from the list field the time in
seconds that the PBX should wait for a signal from the fax machine.
If the dial tone cannot be identified within the configured time frame,
normal call distribution is put into effect, unless the passive modem/
fax call distribution has been enabled.
Select the telephone number of your fax machine from the list field.
If there should be an additional or alternative method for transferring
a fax call received on the telephone to the fax machine, enable the
passive modem/fax call distribution under "Passive". If the user
Distributing Calls on the ISDN Point-to-Multipoint Connection
In the PBX, configure the associated internal
telephone number for each registered MSN.
To do this, open the page displayed in the fig-
ure to the right.
Under "Call distribution for ...", select from
the list field „ISDN Point-to-multipoint con-
nections".
Under "ISDN Point-to-multipoint connec-
tion", select from the list field one of the
already configured Point-to-Multipoint con-
nections.
The MSNs for this connection are listed under
"MSN | name".
Under "Internal no. | name", select an inter-
nal telephone number for each MSN from the
list fields.
Then click "Execute" to apply the settings to
the PBX.
This completes call distribution configuration
on the ISDN Point-to-Multipoint connection.
22
The figure shows you the following page with the settings for
COMset External numbers
under
The figure shows you the following page with the settings for
COMset External numbers
When using an analogue connection or a Point-to-Multipoint connec-
tion (ISDN and VoIP), the internal telephone numbers are individually
assigned to the telephone numbers and MSNs. Automatic call distri-
bution is not possible here.
If multiple internal devices should be accessible over an external tel-
ephone number, an internal group, to which the subscribers in ques-
tion are assigned, is selected as the destination for the call distribu-
tion.
Analogue connections
accepts the call and ends it within three seconds, the call is
automatically transferred to the selected fax machine.
Then click "Execute" to apply the settings to the PBX.
This completes call distribution configuration on the Point-to-
Multipoint connection.
If additional analogue connections are present, under "Analogue
connection", select the next analogue connection from the list field
and configure the settings for it.
Note: For more information on this subject, refer to
and Reachability on page
ISDN connections
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
Example 1 on page 12:
Call distribution
Call Distribution
40.
Example 1 on page 12:
Call distribution