Auerswald COMpact 5010 VoIP Configuration Manual page 71

COMpact 2VoIP module / COMpact 6VoIP
HW requirements
module and inserted USB memory stick
(for voice mail/fax boxes)
SW requirements Version 4.0 (PBX)
Dongle release – – –
Configuration via / COMset
Setting via (scr)
COMset
(scr)
COMset
(scr)
scriber selection in the list field at the top
COMset
Profiles
COMset
Profiles
COMset
fax boxes
COMset
fax boxes
COMset
connections
COMset
nections
COMset
IP (VoIP)
COMset
connections
COMset
nections
nection
COMset
nections
nection
COMset
figurations
COMset
times
COMset
rations
COMset
ing times
COMset
Holidays
COMset
Relay settings
COMset
Call distributions
For explanations concerning the table, see
Configuration of the Feature
Create the required number of configurations and assign each con-
figuration a name as well as an identification number (COMset
Configurations Create configurations).
Now configure the individual configurations as described in the fol-
lowing. To simplify the procedure, you can copy the settings of the
first configuration to the others first (COMset
Copy configurations).
To assign configuration-dependent features to the individual sub-
scribers, first configure the necessary subscriber profiles. (COMset
Internal numbers Subscriber (scr)
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
Features – Function and Configuration
Internal numbers Subscriber
Profiles Configuration
Internal numbers Subscriber
Profiles Profile assignment
Internal numbers Subscriber
Properties Authorizations + sub-
Internal numbers Groups
Configuration
Internal numbers Groups
Profile assignment
Internal numbers Voice mail/
Profiles Configuration
Internal numbers Voice mail/
Profiles Profile assignment
External numbers Analogue
Call distributions
External numbers ISDN con-
Call distributions
External numbers Voice over
Call distributions
External numbers Analogue
Call Forwarding
External numbers ISDN con-
Call Forwarding PTMP con-
External numbers ISDN con-
Call Forwarding PTP con-
Configurations Create con-
Configurations Switching
Configurations Copy configu-
Configurations Copy switch-
Functions Calendar
Door/switching/music module
Door/switching/music module
page 39
Configurations
Profiles Configuration).
Features – Function and Configuration
Then assign the subscriber profile to the existing configurations
(COMset Internal numbers
ment).
To assign configuration-dependent features to the individual groups,
configure the necessary group profiles (COMset
Groups Profiles Configuration). Then assign the group profile
to the existing configurations (COMset
Profile assignment).
To assign configuration-dependent features to the voice mail/fax
boxes, configure the necessary profiles (COMset
Voice mail/fax boxes Profiles
existing profiles to the voice mail/fax boxes (COMset
bers Groups Profiles Profile assignment).
To assign external calls to the internal subscribers, groups and
receptions depending on the configuration, configure external call
distribution including the fallback telephone numbers and the fallback
delay for the existing configurations (COMset
... Call distributions).
To route door calls to internal and external call targets depending on
the configuration, configure the door call distribution for the existing
configurations (COMset Door/switching/music module
tributions).
In order to set the relays as configuration-dependent, configure the
relays with the operation mode "Configuration-dependent" and
assign them to the individual configurations (COMset
ing/music module Call distributions).
To set call forwarding for external numbers as configuration-depend-
ent, configure the call forwarding for the existing configurations
(COMset External numbers
To switch the defined configurations as time-dependent, activate
automatic configuration switching (COMset
ate configurations).
Enter the holidays with irregular switching times compared to the
days of the week into the list of holidays. For this purpose, you can
enter individual dates (e.g., factory holidays) and/or transfer a list of
holidays from the PBX and edit it (COMset
idays).
Enter configuration switching times for the different days of the week
as well as for the holidays. A total of up to 100 switching times are
possible (COMset Configurations
If possible, copy the switching times from one day of the week to the
other (COMset Configurations
Use/Check of Features
1. Enter configurations and switching times.
2. Check switching times under COMset
view switching times.
3. Wait for the switching time to another configuration.
4. Check the current configuration with a system telephone (see the
manual for the telephone).
Dependency/Limitations
In addition to the automatic time-dependent configuration switching
via internal clock it may be started manually via telephone. For this
purpose an identification number has to be assigned to the configu-
ration (COMset Configurations
scriber needs an authorization to switch the configuration manually
(COMset Internal numbers
Authorizations + subscriber selection in the list field at the top).
All holidays entered and activated in the PBX are treated the same
concerning the switching times/configurations. The day of the week
is not considered during the holidays. Therefore in the holiday list
activate only these holidays that have to use special switching times/
configurations different to the days of the week.
Timer and Wake-up Functions
Subscriber (scr) Profile assign-
Internal numbers
Internal numbers Groups
Internal numbers
Configuration). Then assign the
Internal num-
External numbers
Call dis-
Door/switch-
... Call Forwarding ...).
Configurations
Calendar Public hol-
Switching times ...).
Copy switching times).
Configurations
Create configurations). The sub-
Subscriber (scr) Properties
Cre-
Over-
71