Auerswald COMpact 5010 VoIP Configuration Manual page 16

Configuration Manual
Configuration Manual
Example 1: Basic Configuration with Internal Subscribers and Call Distribution
VoIP Subscribers
Assign the VoIP telephones internal tele-
phone numbers from your telephone number
plan.
To do this, open the page displayed in the
figure to the right.
In the "Telephone number" column under
"from:", enter a telephone number from your
telephone number plan.
Under "Name", enter a suitable name with a
maximum of 16 characters.
Under "Device type", select a suitable type
for your end device from the list field.
Click "Execute" to accept the settings in the
PBX.
Configure the settings for any additional telephone numbers.
This completes the configuration of the VoIP subscribers.
Note: If you have contiguous telephone number ranges, you can
enter the beginning and end values under "from: until:" . Only after
clicking "Execute" will the name and device type be available for
entries.
The maximum number of possible VoIP subscribers is specified by
the maximum number of possible internal VoIP channels: In order to
configure VoIP subscribers, at least one internal VoIP channel must
be available. The PBX has two VoIP channels by default. When using
a COMpact 2VoIP module, four VoIP channels are available, and
when using a COMpact 6VoIP module (only for the COMpact 5020
VoIP) eight VoIP channels are available. The number of available
internal VoIP channels is the number of available VoIP channels
minus the VoIP channels reserved for external calls. One external
VoIP channel is set by default from the factory. You can change this
setting on the page Administration
On the page Administration
PIN for each VoIP subscriber (recommended).
Creating Internal Groups
Create the internal groups required.
To do this, open the page displayed in the fig-
ure to the right.
In the "Telephone Number" column under
"from:", enter a telephone number for the
group.
Under "Name" enter a suitable name with a
maximum of 16 characters.
Then click "Execute" to apply the settings to
the PBX.
Configure the settings for all additional groups
required.
Note: If you have contiguous telephone number ranges, you can
enter the beginning and end values under "from: until". Only after
clicking "Execute" will the name be available for entries.
During the configuration process using the configuration assistant, a
group is automatically created for each external telephone number.
You can delete groups, which are no longer needed, on this page.
Click the red recycle bin in the corresponding table line and, subse-
quently, click the green check mark below. Or under "Action", config-
ure Delete and select the groups to be deleted from the left column.
Then click "Execute".
16
The figure shows you the following page with the settings for
COMset
Server configuration.
User PINs, you can configure a user
The figure shows you the following page with the settings for
COMset
Internal numbers Subscriber (scr)
Configure the following settings on a VoIP system telephone: Enter
the Internal number as an MSN and – if configured – the user PIN as
the registration PIN.
Configure the following settings on a standard VoIP telephone or soft
phone: Create a provider named "PBX" and then enter the PBX IP
address as the registrar and domain. Create an account for the pro-
vider "PBX" and enter the internal phone number for the user name
and the associated user PIN as the password – if configured. For
some standard VoIP telephones or soft phones, it might also be nec-
essary to enter the IP address on the PBX as a proxy.
Internal subscribers were already created during the configuration
with the configuration assistant. VoIP subscribers that are no longer
needed can be deleted on this page. Click the red recycle bin in the
corresponding table line and, subsequently, click the green check
mark below. Or under "Action", configure Delete and select the sub-
scribers to be deleted from the left column. Click "Execute".
Internal numbers Groups
COMpact 5010 VoIP/5020 VoIP - Firmware version 4.0 - Configuration Manual 06 08/11
Example 1 on page
Telephone numbers
Example 1 on page
Telephone numbers
12:
VoIP subscribers
12: