Adjustment Of Image Leading Edge Margin; Mounting Of The Host Machine - Canon iR5055 Series Service Manual

Chapter 2
[1]
[1] Feeding direction of paper
7) After the adjustment, perform the following in service mode:
Cassette 3
COPIER > FUNCTION > CST > C3-STMTR/A4R
Register the basic value for paper in Cassette 3:
7-1) Set the STMTR/A4R size papers in Cassette 3, and align the side
guide plate with the STRTR/A4R width.
7-2) Select C3-STMRT/A4R to highlight it and pressing [OK] key
registers the numerical value after auto adjustment.
Cassette 4
COPIER > FUNCTION > CST > C4-STMTR/A4R
Perform the same operation as Cassette 3
<Front Deck Left/Right>
1) Press the set release button to pull out the front deck left/right toward the
front.
2) Loosen the 2 screws [2] and the 2 fixing screws [3] of the deck front cover
[1].
3) Move the cassette guide assembly [1] toward either the front or the back
and perform adjustment.
Move the guide plate toward the back = the left margin is reduced
Move the guide plate toward the front = the left margin is increased
[1]
4) Tighten the 4 screws loosened at the step 2)
5) Close the front deck left/right
6) Check that the left margin of the copied image from the front deck left/
right is as follows : L1=2.5 -/+ 1.5mm
[1]
[1] Feeding direction of paper
2-16
image
F-2-60
[2]
[3]
[1]
F-2-61
F-2-62
image
F-2-63
<Manual Feeder Tray>
1) Open the manual feed tray.
2) Move the side guide plate [1] to the center, and loosen the 2 screws [2] for
the slide guide to adjust the position of the slide guide.
Move the slide guide toward the back = the left margin is reduced
Move the slide guide toward the front = the left margin is increased
[2]
3) Tighten the 2 screws loosened at the step 2)
4) Close the manual feed tray.
<Duplexing Feeder Unit>
1) Make the left margin of the 2nd sided image as L1=2.5 -/+ 2.0mm by se-
lecting the following in service mode:
COPIER > ADJUST > FEED-ADJ > ADJ-REFE
Make the numerical value smaller = the left margin is reduced
Make the numerical value larger = the left margin is increased
(1mm shift by changing every 10 in the setting value)
[1]
[1] Feeding direction of paper

2.2.21 Adjustment of image leading edge margin

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Select the following in the service mode: COPIER > ADJUST > FEED-
ADJ > REGIST
2) Change the setting value to adjust.
(Changing the setting value by 10 moves the image by 1 mm. Increasing
the value moves the image toward the leading edge direction.)
3) Check that the leading edge margin of the image picked up from each cas-
sette/deck is as follows: L1 = 4.0 +1.5/-1.0 mm.
[1]
L1
[1]Feeding direction of paper

2.2.22 Mounting of the Host Machine

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
<Storing of the drum rotational tool and the grip>
1) Detach the lower rear right cover [1].
[1]
F-2-64
image
F-2-65
image
F-2-66
0015-4677
0015-4745