Turning On The Main Power Switch; Toner Stirring; Media Cassette Settings; Index Paper Attachment - Canon iR5055 Series Service Manual

Chapter 2
Use the correct power code to mach the location/area of installation. Make
sure not to leave unused power code at the site.

2.2.14 Turning On the Main Power Switch

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Be sure to remove the packaging materials inside the cassette before turning
on the main power switch.
1) Slide the duplexing unit out, and check to see that there is no foreign sub-
stances or damage in the unit.
2) Make sure that the main power switch is turned off, and then connect the
power plug into the power outlet.
3) Turn on the main power switch.
- The message 'Wait..' appears.

2.2.15 Toner Stirring

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
After wait time, execute toner supply in service mode.
1) Enter service mode.
2) Select: COPIER > FUNCTION > INSTALL > TONER-S.
3) Check the message 'CHECK THE DEVELOPER' appears.
4) Check to see that the developing assembly is attached appropriately, and
then press 'OK'.
- It takes approx. 8 to 10 minutes to supply toner. The machine stops
automatically after counting.
- Make settings for the cassette by the completion of toner supply. (See

media cassette settings.

Be sure not to turn off the machine during its operation.
5) Press [Reset] to escape from service mode.
2.2.16 Media Cassette Settings
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Hold down the cassette release button to slide each cassette to the front.
2) Set the side guide [1] of each cassette onto the hole of the mark M [2] (A4/
A3).
[1]
[2]
3) Attach the inch-series block from inside the cassette onto the hole of the
mark A [1] (STMT-R) and the hole of the mark H [2] (LTR-R) so that
they are hidden.
2-14
F-2-52
-Be sure to attach the inch-series block firmly.
-Go through this procedure only in case of not using inch-series paper.
0015-4668
4) At customer's desire, configure the media cassette settings at service
mode.
5) Place media in the right/left decks.
6) Close the right/left decks. Tear off the relevant media size label [1] from
0015-4669 the mount sheet, and then attach it onto the media size plate of the deck.
7) Hold down the release button, and then slide Cassette3 and 4 out.
8) Tear off the relevant media size label [1] from the mount sheet, and attach
it onto the media size plate [2] of the cassette. Set the media size plate in
the cassette.
0015-4671
9) Close each cassette.

2.2.17 Index Paper Attachment

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Determine the cassette for index paper from either of Cassette 3 or 4.
2) Press the release button of the cassette you determined to slide it toward
the front.
3) Fit the 2 one-touch supports [1] onto the holes [2] of the cassette, and press
the pin into the hole to fix them in place.
4) Fit the holes of the index paper attachment [3] on the one-touch supports
[1].
5) Set the base sheet [4] on the cassette.
[2]
F-2-53
[1]
F-2-54
[1] [2]
F-2-55
[1]
0015-4673