Adjusting The Fixing Inlet Guide; Fixing Web Sensor; Before Removing The Fixing Web Sensor; Removing The Fixing Web Sensor - Canon iR5055 Series Service Manual

[1]
When mounting the fixing inlet guide base, be sure to mount it in the correct
position as checked in the step 1).

9.5.16.3 Adjusting the Fixing Inlet Guide

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
Adjust the solenoid position with the screw [1] so that the fixing inlet guide
positions as indicated in the figure below when the solenoid is turned on.
Fixing roller
Pressure roller
<Points to Note When Adjusting in the Field>
- The fixing inlet guide is at the lower position when the solenoid (SL1)
is turned on.
- The heights at the front and rear sides of the fixing inlet guide should be
adjusted within 0.2mm difference.
- Adjust the height of the fixing inlet guide by loosening the fixing screw
on the height adjusting support plate.

9.5.17 Fixing web sensor

9.5.17.1 Before Removing the Fixing Web Sensor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the fixing front cover. (page 10-16)Reference[Removing the
Fixing Front Cover]
2) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]

9.5.17.2 Removing the Fixing Web Sensor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the fixing web sensor [2].
- 1 connector [1]
F-9-113
[1]
Inlet guide
Solenoid
F-9-114
[2] [1]
F-9-115

9.5.18 Fixing shutter sensor

9.5.18.1 Before Removing the Shutter Sensor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Detach the duplexing feed front cover. (page 10-14)Reference[Remov-
ing the Duplexing Feed Front Cover]
2) Slide out the fixing/feeding unit. (page 9-19)Reference[Removing the
Fixing/Feeding unit]
3) Detach the fixing front cover. (page 10-16)Reference[Removing the
Fixing Front Cover]
4) Detach the fixing/feeding unit front cover. (page 10-15)Reference[Re-
moving the Fixing/Feeding Unit Front Cover]
5) Detach the fixing/feeding unit middle cover. (page
ence[Removing the Fixing/Feeding Unit Middle Cover]
6) Detach the fixing upper cover. (page 10-15)Reference[Removing the
Fixing Upper Cover]
7) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]
8) Remove the fixing upper unit. (page 9-20)Reference[Removing the Fix-
ing Upper Unit]
0015-5069

9.5.18.2 Removing the Shutter Sensor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Remove the shutter sensor support plate [2].
- 1 screw [1]
2) Remove the shutter sensor [1] from the shutter sensor support plate.
0015-8280

9.5.19 Fixing shutter motor

9.5.19.1 Before Removing the Shutter Motor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
0015-5070
1) Detach the fixing front cover. (page 10-16)Reference[Removing the
Fixing Front Cover]
2) Remove the fixing drive assembly. (page 10-22)Reference[Removing
the Fixing Drive Assembly]

9.5.19.2 Removing the Shutter Motor

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N
1) Free the harness from the harness guide [1] and remove the shutter motor
[4].
- 1 connector [2]
- 2 screws [3]
[1]
[2]
F-9-116
[1]
F-9-117
Chapter 9
0015-7199
10-15)Refer-
0015-5071
0015-8281
0015-5072
9-35