Table of Contents
Advertisement
Change History
This page gives information on major changes to the service manual. Please go to the relevant
update.
•
Bus Update May 2011
•
Bus Update September 2011
•
Bus Update June 2012
•
Bus Update February 2013
Bus Update May 2011
The following procedures are updated:
•
12-460-00-171 to 12-462-00-171 HVF Bin 1 Position RAP
•
12L-171 Tri-Folder Not Detected RAP
•
94-549 Drum Runout Calibration Error RAP
•
99-081-00 to 99-112-00 PEST Error 2 RAP
•
OF 5 Boot Up Failure RAP
•
OF 16 POST Error RAP
•
REP 12.19-171 Crease Roll Motor
•
REP 12.27-171 BM Staple Heads
•
REP 91.25 Drum and Front Drum Frame Assembly
•
REP 91.29 Printhead
•
REP 91.34 Drum Pulley
•
Parts List updated
•
GP 7 System Grounding Verification
•
GP 35 Copy and Print Speeds
•
GP 37 Post part Replacement Routines
•
Wiring Diagram 12.10
•
Principles of Operation (System Overview)
Bus Update September 2011
The following procedures are updated:
•
01E +12V Distribution RAP
•
01-525-00 +24V, +/-12V, +5V Short Circuit and Overload RAP
•
12G-110 LCSS PWB Damage RAP
•
19-300-00 to 19-310-00 Image Disk (HDD) Failure RAP
•
99-824-00 to 99-838-00 PEST Error 38 RAP
•
OF 3 Unresponsive Machine RAP
•
OF 16 POST Error RAP
•
REP 1.9 Power Supply Unit
•
REP 3.7 Single Board Controller PWB
•
REP 3.9 NVM Module BWB and Battery
•
REP 3.10 Power Distribution PWB
•
REP 75.11 Tray 5 Elevator Tray Guides
•
REP 91.25 Drum and Front Drum Frame Assembly
•
REP 91.29 Printhead
•
Parts List updated
•
dC 967 Head to Drum Spacing Check
•
Wiring Diagram 1.5 Power Supply Unit (5 of 5)
•
Wiring Diagram 3.3 Single Board Controller PWB (3 of 3)
ColorQube® 9303 Family
•
Wiring Diagram 8.2 Media Path Driver PWB (2 of 5)
•
Wiring Diagram 9.8 Marking Unit Heater PWB
Bus Update June 2012
The following procedures are updated:
•
12-024-00-171, 12-025-00-171 HVF Paddle Roller Position RAP
•
12-113-00-171, 12-114-00-171, 12-190-00-171 HVF BM Entry RAP
•
91-698-00 to 91-732-00 IOD Excessive Head Misalignment RAP
•
91-827-00 PQM Align Needed RAP
•
91-837-00 PQM Align Calibration Needed RAP
•
92-541-00, 92-570-00 Interrupt Storm Fault RAP
•
94-535-00 Drum Driver Command Curent Error RAP
•
94-538-00 to 93-540-00, 93-959-00 Lower Umbilical Thermal Error RAP
•
99-394-00 to 99-413-00 PEST Error 13 RAP
•
99-272-00 to 99-292-00 PEST Error 8 RAP
•
99-444-00 to 99-457-00 PEST Error 16 RAP
•
99-460-00 to 99-477-00 PEST Error 17 RAP
•
OF 3 Unresponsive Machine RAP
•
OF 12 Service Code RAP
•
IQ 9 Deletions in the Process Direction RAP
•
IQ 13 All Colours Uneven RAP
•
REP 91.13 Stitch / Roll Motor
•
REP 91.29 Printhead
•
ADJ 12.2-171 Tri-Folder Paper Settings
•
Parts List updated
•
GP 15 Location and Function of PWB LEDs
•
GP 37 Post Part Replacement Routines
•
Principles of Operation
The following procedures are new:
•
REP 91.37 Stitch / Roll Motor Lead Screws
Bus Update February 2013
This revision of the service manual was produced to meet the requirements for the;
•
introduction of the dicovery 2.0 software platform, system software version
071.XXX.XX.XXX,
GP
33.
•
general update to the ColorQube 9303F procedures.
The following procedures are updated:
•
Introduction. Remote Control Panel information
•
SCP 3 Fault Analysis, warning added
•
SCP 3 Wireless Connectivity RAP information added and GPs 41 to 49
•
12-473-00-171 to 12-478-00-171 Support Finger Position RAP
•
12D-171 Booklet Quality RAP
•
12G-110 LCSS PWB Damage RAP, new figure 1
February 2013
v
Introduction
Change History
Advertisement
Chapters
Table of Contents
