Xerox ColorQube 9303 Series Service Manual page 330

71-101-00 to 71-161-00 Tray 1 Mis-Feed Jam RAP
71-101-00 Tray 1 misfeed jam
71-106-00 LE late to TAR1 sensor from tray 1.
71-130-00 TTM1 TE late at TAR.
71-132-00 TTM1 LE too early at TAR.
71-150-00 TTM1 too long at TAR.
71-151-00 TTM1 too short at TAR.
71-152-00 TTM1 too long at TAR no auto purge.
71-153-00 TTM1 too short at TAR no auto purge.
71-154-00 TTM1 mismatch long at TAR.
71-155-00 TTM1 mismatch short at TAR.
71-160-00 Extra pick retry O.K.
71-161-00 Extra pick retry fail.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check the condition of the paper in tray 1. Refer to
• Check that the paper guides are set correctly.
• Check that the lower left door, PL 70.25 Item 5
• Check the condition of the tray 1 feed, nudger and retard rolls. Use a cloth dampened with
water to clean the rolls, GP 27. If necessary, install a new tray 1 feed roll kit,
Item 28.
• Go to dC135 CRU/HFSI Status. Check the count of the tray 1 feed roll set. If the count is
near end of life, install a new tray 1 feed roll kit,
Procedure
Enter dC330 code 71-101 tray 1 feed sensor, Q71-101,
tray 1 and tray 2. Manually actuate the sensor. The display changes.
Y N
Refer to WD 7.3. Check tray 1 feed sensor, Q71-101. Refer to:
• GP 11 How to Check a Sensor.
• PJ951, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
A
Status Indicator RAPs
71-101-00 to 71-161-00
IQ 1 and GP 20.
is latched correctly.
PL 81.25
PL 81.25 Item 28.
PL 81.25 Item 19. Press Start. Remove
February 2013
A
Install new components as necessary:
• Tray 1 feed sensor, PL 81.25 Item
• 3 tray module PWB, PL 73.16 Item
• Media path driver PWB, PL 1.15 Item
Enter dC330 code 71-395 TAR 1 sensor, Q71-395,
door and manually actuate the sensor. The display changes.
Y N
Refer to WD 7.4. Check takeaway roll sensor 1, Q71-395. Refer to:
• GP 11 How to Check a Sensor.
• PJ955, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• TAR 1 Sensor, PL 73.16 Item
• 3 tray module PWB, PL 73.16 Item
• Media path driver PWB, PL 1.15 Item
Check that the nudger spring is installed correctly,
not damaged. The spring is good.
Y N
Install a new spring, PL 81.25 Item
Enter dC330 code 70-025 3 tray transport motor, MOT70-025,
The motor runs.
Y N
Refer to WD 7.5. Check MOT70-025. Refer to:
• GP 10 How to Check a Motor.
• PJ956, 3 tray module PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• 3 tray transport motor, PL 73.16 Item 3
• 3 Tray Module PWB, PL 73.16 Item
• Media path driver PWB, PL 1.15 Item
Observe the takeaway rolls, PL 73.16. The takeaway rolls rotate.
Y N
Check the drive belt and gears,
Check the condition of the takeaway rolls,
Y N
Clean or install new takeaway rolls,
B
2-306
19.
4.
5.
PL 73.16 Item 11. Press Start. Open the left
11.
4.
5.
PL 81.25 Item 10. Check that the spring is
10.
PL 73.16 Item
4.
5.
PL 73.16 Item 7.
PL 73.16. The takeaway rolls are good.
PL 73.16 Item 9.
ColorQube® 9303 Family
3. Press Start.