Table of Contents
Advertisement
3rd line (Log No. No.=xxx2, xxx6, xxxA, xxxE lines)
Logger mem pointer : Log No.
log_rp = 0000B1E0 : No = 0BF2 : 010A0A0A 070F0010 00 00000001 00000000
@, : H_DPR_REG0_3 (EE/PB control)
@. : H_DPR_REG0_2 (C1 error correction ability (e+n))
#/ : H_DPR_REG0_1 (C1 error correction ability (e))
#- : H_DPR_REG0_0 (C1 error correction ability (n))
#= : H_DPR_REG0_7 (IC test report (c1_enc))
#[ : H_DPR_REG0_6 (IC test report (c1_dec))
#] : H_DPR_REG0_5 ((not used))
#\ : H_DPR_REG0_4 (test mode control)
#; : H_DPR_REG0_B (C1 random error (Cch))
#' : H_DPR_REG0_A (C1 random error (Bch))
#, : H_DPR_REG0_9 (C1 random error (Ach))
#. : H_DPR_REG0_8 (C1 correction control)
$/ : H_DPR_REG0_F (option mode DATA resistor)
$- : H_DPR_REG0_E (option mode ADDRESS resistor)
$= : H_DPR_REG0_D ((not used))
$[ : H_DPR_REG0_C (C1 random error (Dch))
4th line (Log No. No.=xxx3, xxx7, xxxB, xxxF lines)
Logger mem pointer : Log No.
log_rp = 0000B1F0 : No = 0BF3 : FF0A0A0A D0D0D000 00 F8FCFCD0 C8FFFFF9
$] : H_DPR_REG1_3 (erasure off/C2 dec control)
$\ : H_DPR_REG1_2 (C2 error correction ability (e+n))
$; : H_DPR_REG1_1 (C2 error correction ability (e))
$' : H_DPR_REG1_0 (C2 error correction ability (n))
$, : H_DPR_REG1_7 (C1 burst error (Cch))
$. : H_DPR_REG1_6 (C1 burst error (Bch))
%/ : H_DPR_REG1_5 (C1 burst error (Ach))
%- : H_DPR_REG1_4 (REC_ENABLE/SAT ON/OFF control)
%= : H_DPR_REG1_B (Mechanism adjustment signal generation control)
%[ : H_DPR_REG1_A (Mechanism adjustment REC ENABLE control)
%] : H_DPR_REG1_9 (FM parity err)
%\ : H_DPR_REG1_8 (C1 burst error (Dch))
%; : H_DPR_REG1_F (read exor data)
%' : H_DPR_REG1_E (Processor test mode)
%, : H_DPR_REG1_D (IC test report (c2 enc/dec))
%. : H_DPR_REG1_C (IC test control (diag mode))
GY-2120WD/WS
: Sys ID
R/W Len R6 TCR
@, #/
#= #]
@. #-
#[ #\
: Sys ID
R/W Len R6 TCR
$] $;
$, %/
$\ $'
$. %-
TCR UB
#; #,
$/ $=
#' #.
$- $[
TCR UB
%= %]
%; %,
%[ %\
%' %.
6-2. Description of Commands
6-65
Advertisement
Table of Contents
Troubleshooting
