Toro Greensmaster 1018 Service Manual page 126

Assembling the Handle Assembly (continued)
Controls, Wheels and Accessories : Service and Repairs
4. Position the clutch bail link (5) in the handle mount (7). Install the spacer tube
(17) and 2 flange bushings (3) to the handle mount. Secure the clutch bail
link to the handle mount with the bolt (2) and flange nut (8).
5. Position the compression spring (6), spacer tube (17) and 2 bushings (3) into
the handle mount (7). Install the clutch bail assembly (4) to the handle mount
(7) and secure with the bolt (2) and flange nut (8).
6. If removed, install the LH and RH bail brackets (1 and 19) to the handle
(20) with the 2 screws (18).
7. Install the clutch bail assembly (4) to the handle (20). Secure the handle to
the handle mount (7) with the 2 bolts (21) and 2 nuts (8).
8. If removed, install the 3 spacers (item 20 in
nuts (15) to the upper receiver weldment (8).
9. Position the spring spacer (24) and handle torsion spring (23) into the handle
adjuster assembly (22). Install the handle adjuster assembly to the upper
receiver weldment (8) with the bolt (21) and nut (15).
10. If removed, install the lift assist handle (27) to the upper receiver weldment
(8) and secure with the bolts (16 and 11).
11. Slide the upper receiver weldment (8) in to the lower handle assembly (19)
and secure with the bolt (29) and flange nut (9).
Note: Do not tighten bolt and nut. Install the nut to engage locking feature.
The upper receiver weldment (8) must be free to slide.
12. Reposition the wire harness.
13. Install the conduit clamps (10) to the upper receiver weldment (8) and lower
handle assembly (19) and secure with screws (11).
14. If removed, install the flange bushings (5), bolt (12) and flange nut (13) into
the brake lever (6).
15. Position the brake lever (6) to the upper receiver weldment (8) and secure
with the shoulder screw (4) and flange nut (7).
16. Install the handle notepad plate (2) to the handle assembly (3) and secure
with the 4 plastite screws (1).
17. Install the engine ON/OFF switch to the handle assembly.
18. Install the wire harness.
19. If removed, install the flange bushings (35) inside the throttle arm (36).
20. If removed, slide the throttle lever (34) onto the throttle arm (36) and secure
with screw (32).
21. Torque tighten the bolt from 2.2 to 3.4 N·m (20 to 30 in-lb).
22. Install the throttle arm (36) to the handle assembly (3) and secure with bolt
(30), compression spring (31) and nut (37).
23. Install the bolt (38) and 2 flange nuts (7) to the upper receiver weldment (8).
Ensure that the head of the bolt is resting the on throttle arm (36).
24. Install the brake latch shaft; refer to
7–17).
25. Install the clutch and reel drive lever assembly; refer to
Clutch and Reel Drive Engagement Lever Assembly (page
26. Install the reel cable; refer to
27. Install the brake cable; refer to
28. Install the clutch cable; refer to
Assembling the Brake Latch Shaft (page
Installing the Reel Cable (page
Installing the Brake Cable (page
Installing the Clutch Cable (page
Page 7–22
Figure 58), 3 bolts (21) and 3
Assembling the
7–15).
7–13).
7–8).
7–10).
Greensmaster ® 1018/1021/1026
18238SL Rev B