Maintenance - Roland monoFab SRM-20 User Manual

Important Notes on Care and Maintenance . . . . . . . . 92
Cleaning after Cutting Operation Ends . . . . . . . . . . . . 93
Cleaning the X-/Z-Shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Replacement of the Consumable Parts . . . . . . . . . . . . 96
Caution and Note for Replacement of the Consumable Parts . . 96
Replacement Cycles and Replacement Methods of Consumable Parts . . 96
Confirm the Total Spindle Motor Rotation Time . . . . . . . . . . . . . . 97
Run in the Spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Replacement the Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
What to Do If... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Initialization Is Not Performed / Initialization Fails . . . . . . . . . . . 100
VPanel Does Not Recognize the Machine . . . . . . . . . . . . . . . . . . . 100
Operations Are Ignored . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
The Spindle Doesn't Rotate / Spindle Rotation Speed Is Wrong . . 102
The Feed Rate is Wrong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Abnormal Cutting is Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
The Origin is Misaligned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
The Cutting Results are Not Attractive . . . . . . . . . . . . . . . . . . . . . . 104
It Takes Time to Delete Data After Quitting Cutting . . . . . . . . . . 104
The Power Turns Off After Cutting Ends . . . . . . . . . . . . . . . . . . . . . 105
The Cutting Tool Does Not Reach the Material . . . . . . . . . . . . . . 105
The Driver Cannot Be Installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Uninstalling the Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Abnormal Noise Occurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Maintenance

Changing the Position of a Spindle Unit . . . . . . . . . . . . . . . . . . . . 111
Initializing This Machine's Settings . . . . . . . . . . . . . . . . . . . . . . . . . 114
Displaying This Machine's Settings . . . . . . . . . . . . . . . . . . . . . . . . . 115
Confirm the Version Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Responding to Error Messages . . . . . . . . . . . . . . . . . . 117
Massage is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117