Teledyne T360 Operation Manual page 15

LIST OF FIGURES
Figure 3-1: Front Panel Layout ...................................................................................................................... 27
Figure 3-2: Display Screen and Touch Control ............................................................................................. 28
Figure 3-3: Display/Touch Control Screen Mapped to Menu Charts............................................................. 30
Figure 3-4: Rear Panel Layout....................................................................................................................... 31
Figure 3-5: Internal Chassis Layout............................................................................................................... 33
Figure 3-6: Optical Bench Layout .................................................................................................................. 34
Figure 3-7: Analog In Connector.................................................................................................................... 36
Figure 3-8: Current Loop Option Installed on the Motherboard..................................................................... 39
Figure 3-9: Control Inputs Power Connections.............................................................................................. 41
Figure 3-10: Alarm Relay Output Pin Assignments ......................................................................................... 42
Figure 3-11: Basic Internal Gas Flow .............................................................................................................. 45
Figure 3-12: Pneumatic Connections-Basic Configuration-Using Bottled Span Gas .................................... 46
Figure 3-13: Pneumatic Connections-Basic Configuration-Using Gas Dilution Calibrator ............................ 46
Figure 3-14: Pneumatic Connections with Ambient Zero/Ambient Span Valves (OPT 50A) .......................... 48
Figure 3-15: Pneumatic Connections with Ambient Zero/Ambient Span Valves (Opt 50A) and
External Zero Air Scrubber.......................................................................................................... 48
Figure 3-16: Internal Pneumatic Flow - Ambient Zero/Ambient Span ............................................................ 49
Figure 3-17: Pneumatic Connections with Ambient Zero/Pressurized Span Valves (OPT 50B) .................... 50
Figure 3-18: Pneumatic Connections with Ambient Zero/Pressurized Span Valves (Opt 50B) and
External Zero Air Scrubber.......................................................................................................... 51
Figure 3-19: Internal Pneumatic Flow - Ambient Zero/Pressurized Span Valves........................................... 52
Figure 3-20: Example of Pneumatic Set up for Multipoint Calibration............................................................. 53
Figure 3-21: O2 Sensor Calibration Set Up ..................................................................................................... 61
Figure 3-22: Internal Pneumatics with O2 Sensor Option 65 .......................................................................... 62
Figure 4-1: Front Panel Display ..................................................................................................................... 67
Figure 4-2: Viewing TEST Functions ............................................................................................................. 70
Figure 4-3: Viewing and Clearing T360 WARNING Messages ..................................................................... 72
Figure 4-4: Default DAS Channels Setup ...................................................................................................... 80
Figure 4-5: APICOM User Interface for DAS Configuration .......................................................................... 94
Figure 4-6: Analog Output Connector Pin Out............................................................................................... 95
Figure 4-7: Rear Panel Connector Pin-Outs for COM1 & COM2 in RS-232 Mode ..................................... 109
Figure 4-8: CPU Connector Pin-Outs for COM1 & COM2 in RS-232 Mode ............................................... 110
Figure 4-9: Jumper and Cables for Multidrop Mode .................................................................................... 123
Figure 4-10: RS-232-Multidrop Host-to-Analyzer Interconnect Diagram....................................................... 124
Figure 4-11: Setup for Calibrating Analog Voltage Outputs .......................................................................... 141
Figure 4-12: Setup for Calibrating Current Outputs....................................................................................... 142
Figure 4-13: Status Output Connector........................................................................................................... 152
Figure 4-14: Control Inputs ............................................................................................................................ 154
Figure 4-15: APICOM Remote Control Program Interface ............................................................................ 161
Figure 5-1: Pneumatic Connections-Basic Configuration-Using Bottled Span Gas .................................. 170
Figure 5-2: Pneumatic Connections-Basic Configuration-Using Gas Dilution Calibrator .......................... 171
Figure 5-3: Pneumatic Connections - Ambient Zero/Pressurized Span Valves ........................................ 174
Figure 5-4: Pneumatic Connections - Ambient Zero/Pressurized Span Valves and External Zero Air
Scrubber .................................................................................................................................... 174
Figure 5-5: Pneumatic Connections - Ambient Zero/Ambient Span Valves ............................................... 175
Figure 5-6: Pneumatic Connections - Ambient Zero/Ambient Span Valves with External Zero Air
Scrubber .................................................................................................................................... 175
Figure 6-1: Sample Particulate Filter Assembly .......................................................................................... 190
Figure 7-1: Measurement Fundamentals..................................................................................................... 194
Figure 7-2: GFC Wheel................................................................................................................................ 194
Figure 7-3: Measurement Fundamentals with GFC Wheel ......................................................................... 195
Figure 7-4: Affect of CO2 in the Sample on CO2 MEAS & CO2 REF......................................................... 196
Figure 7-5: Effects of Interfering Gas on CO2 MEAS & CO2 REF.............................................................. 197
07272B DCN6552
Teledyne API Model T360/T360M Operation Manual
xiii